background image

13

WILD HOTS-Item code:BH84                                    Instruction Manual.

INSTALLING THE RECEIVER AND BATTERY.

Battery.

Tie wrap.

 

  

  

1) It is critical that your airplane be bal-

anced correctly. Improper balance will cause
your plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED
115MM BACK FROM THE LEADING EDGE
OF THE WING.

 

  

  

2) Mount the wing to the fuselage. Using a

couple of pieces of masking tape, place them
on the top side of the wing 115 mm back from
the leading edge, at the fuselage sides.

BALANCING.

Receiver.

 

  

  

3.  Turn the airplane upside down. Place

your fingers on the masking tape and care-
fully lift the plane .

Accurately mark the balance point on the top
of the wing on both sides of the fuselage. The
balance point is located 115mm back from the
leading edge. This is the balance point at which
your model should balance for your first flights.
Later, you may wish to experiment by shifting
the balance up to 10mm forward or back to
change the flying characteristics. Moving the
balance forward may improve the smooth-
ness and arrow- like tracking, but it may  then
require more speed for take off  and make it
more difficult to slow down for landing. Moving
the balance aft makes the model more agile
with a lighter and snappier ”feel”. In any case,
please start at the location we recommend .

Содержание WIlD HOTS















Отзывы: