Black Horse Model SPEED AIR BH.08 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 19

Black Horse Model SPEED AIR BH.08 Скачать руководство пользователя страница 18

SPEED AIR-40.

Instruction Manual.

18

1) It is critical that your airplane be balanced

correctly. Improper balance will cause your
plane to lose control and crash.

THE CENTER OF GRAVITY IS LOCATED

100mm

BACK FROM THE LEADING EDGE

OF THE WING.

BALANCING.

2) Turn the airplane upside down. Place

your fingers on the masking tape and carefully
lift the plane .

ATTACHMENT WING-FUSELAGE.

See pictures below:

Remove covering.

Mark point.

Accurately mark the balance point on the top
of the wing on both sides of the fuselage. The
balance point is located 100mm back from the
leading edge. This is the balance point at which
your model should balance for your first flights.
Later, you may wish to experiment by shifting
the balance up to 10mm forward or back to
change the flying characteristics. Moving the
balance forward may improve the
smoothness and arrow- like tracking, but it may
then require more speed for take off and make
it more difficult to slow down for landing.
Moving the balance aft makes the model more
agile with a lighter and snappier ”feel”. In any
case, please start at the location we
recommend .

«
...
16
17
18
19
»

Содержание SPEED AIR BH.08




















Отзывы:

Нет отзывов