Black Horse Model HEINKEL HE-112B Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 17

Black Horse Model HEINKEL HE-112B Скачать руководство пользователя страница 5

HEINKEL HE-112B Item code: BH159

1. INSTALLING THE AILERONS, FLAPS

2. INSTALLING THE AILERON SERVOS, FLAPS

Temporary pin to
keep hinge centered.

C/A glue.

C/A glue.

* Apply drops of thin CA to the top and bottom of each
hinge. Do not use CA accelerator. After the CA has fully
hardened, test the hinges by pulling on the aileron.

*

Test fit the ailerons to the wing with the hinges. If the

hinges don’t remain centered, stick a pin through the
middle of the hinge to hold it in position.

* Secure nylon hinges with instant glue, being careful
not to glue the wing and aileron together.
* Align the center line of main wing with aileron.

Make certain the hinges are adequately secured

with glue. if they come loose in flight accidents may
result.

WARNING

Flap

Aileron

Bottom view

2x10mm

2x10mm

Servo tray

5

1.

Install the rubber grommets and brass eyelets on to

the aileron servos.

2.

Using a modeling knife, remove the covering from

over the pre-cut servo arm exit hole on the aileron servo
tray / hatch. This hole will allow the servo arm to pass
through when installing the aileron pushrods.

3.

Place the servo into the servo tray. Center the servo

within the tray and drill 1.5mm pilot holes through the
block of wood for each of the four mounting screws
provided with the servo.

4.

Using the thread as a guide and using masking

tape, tape the servo lead to the end of the thread:
carefully pull the thread out. When you have pulled the
servo lead out, remove the masking tape and the servo
lead from the thread.

Drill a hole 1.5mm

and s

ecure

o

90

o

60

Flap

Aileron

2x10mm

2 x 10mm Screw

- - - - -- - 16

5.

Place the servo into the servo tray/ hatch into the

servo box on the bottom of the wing and drill 1.5mm
pilot holes through the tray and servo box for each of
the four mounting screws. Secure the servo tray in
place using the mounting screws provided.

«
...
3
4
5
6
7
...
»

Содержание HEINKEL HE-112B


















Отзывы:

Нет отзывов