manualshive.com logo in svg

Black Horse Model HEINKEL HE-112B, Инструкция по эксплуатации, Страница: 11 / 17

Поделиться
Скачать
Black Horse Model HEINKEL HE-112B Скачать руководство пользователя страница 11

HEINKEL  HE-112B                                                                                         Item code: BH159  

When you are sure that everything is aligned correctly, 

mix up a generous amount of 30 minute epoxy. Apply a 

thin  layer  to  the  top  and  bottom  of  the  stabilizer 

mounting area and to the stabilizer mounting platform 

sides in the fuselage. Slide the stabilizer in place and 

re-align. Double check all of your measurements one 

more time before the epoxy cures. Remove any excess 

epoxy using a paper towel and rubbing alcohol and hold 

the stabilizer in place with T-pins or masking tape.

A/B Epoxy glue

After  the  epoxy  has  fully  cured,  remove  the  masking 

tape or T-pins used to hold the stabilizer in place and 

carefully inspect the glue joints. Use more epoxy to fill in 

any gaps that may exits that were not filled previously 

and  clean  up  the  excess  using  a  paper  towel  and 

rubbing alcohol.

C/A glue

8.2. ELEVATOR PUSHROD INSTALLATION

M2 Lock nut

M2

Elevator pushrod

Bottom side.

Silicone Tube

Top side and
bottom side

8.1. ELEVATOR CONTROL HORN
INSTALLATION

Elevator  control  horn  install  as  same  as  the  way  of 

aileron control horn.

Control horn

Bottom side.

1)   

Using pliers, carefully make a 90 degree bend down 

at  the  mark  made.  Cut  off  the  excess  wire,  leaving 

about 6mm beyond the blend.

2)   

Insert the 90 degree bend down through the hole in 

the servo arm. Install one nylon snap keeper over the 

wire  to  secure  it  to  the  arm.  Install  the  servo  arm 

retaining screw.

11

M2 

Nut

800 mm Push rod

 - - 2

 - - - 2

 

- - 2

 - - - - - 

Horn 

  - - - - - 2

  - - - - - 1

 - - - - 2

Flaslink

  - - - - - 2

5mm Silicone Tube

 

1

 - - - 

100mm Push rod

Horn

Silicone Tube

Elevator servo

Elevator pushrod

Secure.

Cut

Snap keeper

Flaslink

Pushrod wire

servo arm

Fuselage bottom side

Содержание HEINKEL HE-112B


















Отзывы:

Нет отзывов