Black Horse Model HEINKEL HE-112B Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 17

Black Horse Model HEINKEL HE-112B Скачать руководство пользователя страница 1

Instruction Manual Book

HEINKEL HE-112B

Item code: BH159.

NOT INCLUDING ELECTRIC RETRACT GEAR.
ONLY INCLUDING OLEO STRUTS.
ALL BALSA - PLY WOOD CONSTRUCTION.
COVERED IN A HEAT-SHRINK FILM WITH PRINTED

.

95% ALMOST READY TO FLY

SPECIFICATION:

- Wingspan: 1,550mm (61.02in).
- Length: 1,560mm (61.42in).
- Weight: 4.5kg (9.9lbs).

2

- Wing area: 49.0 dm .

2

- Wing loading: 91.8 g/dm .
- Servo mount: 42mm x 21mm.
- Wing type: Naca Airfoil.
- Spinner: 80mm.
- Gear type: Electric retract gear,
size: (92.2 x 51 x 30.6)mm (not included).
Oleo struts (included).

Parts listing required (not included):

- Radio: 06 channels.
- Servo: 07 - 08 servos.
- Engine: 61 - 91 ; 15 cc Gas.
- Motor: Brushless outrunner 1200-2200W, 650KV.
- Propeller: Suit with your engine.

Recommended Motor
and Battery set up (not included):

- Motor: RIMFIRE.60.
- Lipo cell: 6 cells 4,000-5,000mAh.
- Receiver battery: 6V/ 1200-2000mAh NiMH.
- ESC: 80A.

Made in Vietnam.

1
2
3
...
»

Содержание HEINKEL HE-112B


















Отзывы:

Нет отзывов