background image

7

ENGLISH

(Original instructions)

Electrical safety

#

This tool is double insulated; therefore no earth 

wire is required. Always check that the power 

supply corresponds to the voltage on the rating 

plate.

u

 

If the supply cord is damaged, it must be replaced by the 

manufacturer or an authorised BLACK+DECKER Service 

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed control knob

2. On/off switch

3. Lock-on button

4. Secondary handle

5. Belt tensioning lever

6. Belt tracking knob

7. Straight arm

Fig. A

9. Narrow arm (Where supplied)

10. Cranked arm (Where supplied)

Fig. D

13. Dustbag (Where supplied)

14. Dust cassette

15. Deflector

Assembly

Warning!

 Before assembly, make sure that the tool is

switched off and unplugged.

Fitting and removing sanding arms (fig. A)

Before first use, you must fit a sanding arm to the tool. Your

tool is supplied with the following:

u

  A straight arm (7, sanding width 13 mm).

These parts are also available as an accessory from your

BLACK+DECKER dealer, (not available in Australia and

New Zealand).

Fitting

u

  Make sure that the belt tensioning lever (5) is in the 

  position shown.

u

  Loosen and remove the belt tracking knob (6).

u

  Remove the tape retaining the spring (8) (if present).

u

  Check that the spring (8) is located in its mounting hole.

u

  Position the arm (7, 9 or 10) as shown.

u

  Fit the belt tracking knob (6) and tighten it until the arm (7) 

is aligned with the tool.

Removing

u

  Remove the sanding belt (12) (if present) as described 

below.

u

  Loosen and remove the belt tracking knob (6).

u

  Remove the arm (7, 9 or 10).

Warning!

 Be careful not to lose the spring (8).

Fitting and removing sanding belts (fig. B)

Warning!

 The spring must be fitted. Be careful not to lose the

spring (8).

Fitting

u

  Move the belt tensioning lever (5) to the front position (A).

u

  Make sure that the arrows on the inside of the sanding 

belt (12) face the same direction as the arrows (17) on the 

housing.

u

  Place the sanding belt (12) over the front pulley (11) and 

the rear pulley (16), sliding it through the slot in the 

  housing.

u

  Move the belt tensioning lever (5) to the rear position (B).

u

  Adjust the belt tracking as described below.

Removing

u

  Move the belt tensioning lever (5) to the front position (A).

u

  Slide the sanding belt (12) off the pulleys.

Adjusting the sanding belt tracking (fig. C)

u

  Switch the tool on.

u

  Turn the belt tracking knob (6) as required until the 

  sanding belt runs straight along the length of the arm.

Fitting and removing the dust cassette or the dust 

bag (fig. D, E and F) (Where supplied)

Warning!

 Always remove the dustbag or dust cassette and fit

the deflector when using the tool on metal workpieces.

Fitting

u

  Fit the dust cassette (14) or the dustbag (13) over the dust 

extraction outlet.

u

  Slide the item (13 or 14) onto the tool and make sure that 

it is securely located.

Removing

u

  To remove the dust cassette (14), or the dustbag (13), pull 

the item (13 or 14) to the rear and off the outlet.

Fitting and removing the deflector (fig. D and E)

Warning!

 The deflector must be used when sanding metal

workpieces.

Fitting

u

  Fit the deflector (15) over the dust extraction outlet.

Содержание KA900E













Отзывы: