Black+Decker GL933, Оригинальное руководство пользователя

Страница: 9 / 12

9
ENGLISH (Original instructions)
To adjust the height setting, proceed as follows:
u
Release the height adjust locking clamp (16).
u
Gently pull the tube (7) up or down to the desired height.
u
Close the height adjust locking clamp (16).
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
u
Remove the tape holding the cutting line to the spool
housing (12).
Storing the spool not in use (fig. G)
The tool has two cutting systems:.
u
AFS: Single line autofeed for light trimming and edging.
u
HDL: Heavy Duty Dual Line cutting system for more
overgrown areas.
Note: The HDL spool may be used in trimming mode only.
The cutting system not in use can be stored in the spare spool
storage.
u
Align the tabs (17) on the spool cover with the cut outs
(18) in the spare spool storage (8).
u
Push the cover onto the spare spool storage until it snaps
securely into place.
Connecting the tool to the mains (fig. H)
u
Connect the female plug of a suitable extension cable to
the power inlet (4).
u
Loop the cable through the cable restraint (3).
u
Insert the mains plug into a mains outlet.
For wired in cable units: Make sure the cable is looped
through the cable restraint prior to connecting the plug to the
mains outlet.
Warning! The extension cable must be suitable for outdoor
use.
Use
Warning! Let the tool work at its own pace. Do not overload.
Setting the tool to trimming or edging mode
(fig. I & J)
The tool can be used in trimming mode as shown in fig. I or in
edging mode to trim overhanging grass along lawn edges and
flower beds as shown in fig. J.
Trimming mode (fig. I)
For trimming, the trimmer head should be in the position
shown in fig. I. If it is not:
u
Release the height adjust locking clamp (16).
u
Rotate the tube (7) clockwise.
u
When the head is in position, close the height adjust
locking clamp (16).
Note: The tube will only rotate in one direction.
Note: The HDL spool may be used in trimming mode.
Edging mode (fig. J)
For edging, the trimmer head should be in the position shown
in fig. J. If it is not:
u
Release the height adjust locking clamp (16).
u
Rotate the tube (7) anti-clockwise.
u
When the head is in position, close the height adjust
locking clamp (16).
Note: The tube will only rotate in one direction.
Switching on and off
u
To switch the tool on, squeeze the on/off switch (1).
u
To switch the tool off, release the trigger lever.
Warning! Never attempt to lock the trigger lever in the on
position.
Hints for optimum use
General
u
In order to achieve optimum cutting results, only cut dry
grass.
Trimming
u
Hold the tool as shown in fig. K.
u
Gently swing the trimmer from side to side.
u
When cutting long grass, work in stages from the top. Take
small cuts.
u
Keep the tool away from hard objects and delicate plants.
u
Cutting line will wear faster and require more feeding if
the cutting is done along pavements or other abrasive
surfaces or heavier weeds are being cut.
u
If the tool starts running slowly, reduce the load.
Edging
Optimum cutting results are achieved on edges deeper than
50 mm.
u
Do not use the tool to create edges. To create edges, use
an edging spade.
u
Guide the tool on its wheel as shown in fig. L.
u
To make a closer cut, slightly tilt the tool.
Fitting a new spool of cutting line (fig. M & N)
Replacement spools of cutting line are available from your
BLACK+DECKER dealer (cat. no. A6482). Packs containing 3
spools of cutting line are also available (cat. no. A6486).
u
Unplug the tool.
u
Keep the tabs (17) depressed and remove the spool cover
(21) from the housing (12) (fig. M).
u
Remove the empty spool (22) from the spool cover.
u
Remove any dirt and grass from the spool cover and
housing.
u
Unclip the end of of the cutting line and guide the line into
the eyelet (23) (fig. M). The line should protrude approx.
11 cm from the spool cover.