Black+Decker EVO186, Руководство пользователя

Страница: 7 / 16

7
ENGLISH
Electrical safety
#
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains volt-
age corresponds to the voltage on the rating plate.
Never attempt to replace the charger unit with a
regular mains plug.
u
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black+Decker Service Cen-
tre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Head release button
4. Bit holder
5. Battery
6. Battery release button
7. Drill/screwdriver head/ Hammer drill head
8. Torque adjustment collar
9. Chuck
10. LED work light
11. Charging indicator
12. Charger
13. Speed selector
14. Clutch marking
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. A)
u
To fit the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
u
To remove the battery, push the release button (6) while at
the same time pulling the battery out of the receptacle.
Fitting and removing tool heads (fig. B)
Warning! Care must be taken when fitting and removing
heads. Moving parts may become hot during use.
u
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
u
To remove a tool head, depress the head release button
(3) and take the head off the tool.
u
To fit a tool head, line it up with the tool as shown and
push it onto the tool until it snaps into place.
Fitting and removing a drill bit or screwdriver bit
The drill/screwdriver head is fitted with a keyless chuck to
allow for an easy exchange of bits.
u
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
u
Open the chuck (9) by turning the front part clockwise with
one hand while holding the rear part with the other.
u
Insert the bit shaft into the chuck (9).
u
Firmly tighten the chuck (9) by turning the front part anti-
clockwise with one hand while holding the rear part with
the other.
u
To remove the screwdriver bit from the bit holder, lift the bit
from the recess.
u
To store the screwdriver bit, firmly push it into the holder.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Charging the battery (fig. C)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u
To charge the battery (5), insert it into the charger (12).
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
u
Plug in the charger and switch on at the mains.
The charging indicator (11) will flash green continuously
(slowly).
The charge is complete when the charging indicator (11)
lights green continuously. The charger and the battery can be
left connected indefinitely with the LED illuminated. The LED
will change to flashing green (charging) state as the charger
occasionally tops off the battery charge. The charging indica-
tor (11) will be lit as long as the battery is connected to the
plugged-in charger.
u
Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
ing indicator (11) will flash red at a fast rate. Proceed as
follows: