Black+Decker BDCJS12U, Руководство пользователя

Страница: 6 / 28

6
ENGLISH
‹ ‹
The charger and the battery can be left connected
indefinitely.
‹ ‹
Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Fitting and removing the battery (fig. B)
‹ ‹
To fit the battery (8), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push up until
the battery snaps into place.
‹ ‹
To remove the battery, push the release button (10) while
at the same time pulling the battery out of the receptacle.
Fitting and removing the saw blade (fig. C)
‹ ‹
Hold the saw blade (7) with the teeth facing forward.
‹ ‹
Lift the saw blade locking lever (3) upwards.
‹ ‹
Insert the shank of the blade fully into the blade clamp (4)
as far as it will go.
‹ ‹
Release the lever.
‹ ‹
To remove the saw blade (7), lift the saw blade locking
lever (3) upwards and pull the blade out.
Switching on and off (fig. D)
‹ ‹
To switch on, slide the lock off switch (2) to the left then
pull and hold the variable on/off trigger switch (1).
‹ ‹
To switch off, release the trigger switch (1).
Warning! Do not switch the tool on or off while under load.
Warning! Always slide the lock off switch (2) to the right, the
locked position when the tool is not in use.
Storage of spare blades (fig. E)
‹ ‹
Spare blades (7) can be stored in the recess (12) on the
main body of the tool.
Sawing
‹ ‹
Always hold the tool with both hands.
‹ ‹
Let the blade run freely for a few seconds before starting
the cut.
‹ ‹
Apply only a gentle pressure to the tool while performing
the cut.
‹ ‹
If possible, work with the shoe plate (6) pressed against
the workpiece. This will improve tool control and reduce
tool vibration, as well as prevent the blade from being
damaged.
Sawing laminates
As the saw blade cuts on the upward stroke, splintering may
occur on the surface closest to the shoe plate.
‹ ‹
Use a fine-tooth saw blade.
‹ ‹
Saw from the back surface of the workpiece.
‹ ‹
To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw through
this sandwich.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
‹ ‹
Use a saw blade suitable for sawing metal. Use a finetooth
saw blade for ferrous metals and a coarser saw blade for
non-ferrous metals.
‹ ‹
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut through
this sandwich.
‹ ‹
Spread a film of oil along the intended line of cut.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
This tool is suitable both for U-shank and T-shank saw blades
Technical data
BDCJS12U
Voltage V
DC
12
No-load speed Min
-1
0 - 2800 SPM
Stroke Length mm 16
Max depth of cut:
Wood mm 52
Steel mm 5
Aluminium mm 17
Weight kg 1.19 (with battery 1.44)
Battery BDCB12U
Voltage V
DC
12
No-load speed Ah 1.5
Stroke Length Li-Ion
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.Your charger does not require any
maintenance apart from regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning