Black+Decker BCRT8I, Оригинальное руководство пользователя

Страница: 10 / 136

10
ENGLISH (Original instructions)
Storage Recommendations
The best storage place is one that is cool and dry, away from
direct sunlight and excess heat or cold. Store the fully charged
tool disconnected from the USB cable.
Transportation
Note: Integral Li-ion tools should not be put in checked
baggage on airplanes and must be properly protected from
short circuits if they are in carry-on baggage.
Important safety instructions for all integral battery
charging
@
Warning! Read all safety warnings, instructions,
and cautionary markings for the battery, USB
cable and product. Failure to follow the warnings
and instructions may result in electric shock, fire
and/or serious injury.
u
The provided USB cable is not intended for any uses
other than charging BLACK+DECKER rechargeable
tools with micro USB ports. Charging other types of
tools may cause their batteries to overheat and burst,
resulting in personal injury, property damage, fire, electric
shock or electrocution.
u
Use only with the Listed/Certified Information
Technology (computer) Equipment.
u
DO NOT expose USB cable to water, rain or snow.
u
Pull by the plugs rather than the cord when
disconnecting the USB cable. This will reduce the risk of
damage to the plugs and cord.
u
Make sure that the cord is located so that it will not
be stepped on, tripped over or otherwise subjected to
damage or stress.
u
When charging the tool outdoors, always provide a
dry location.
u
DO NOT use a USB cable with a damaged cord or
plugs. Have them replaced immediately.
u
Foreign materials of a conductive nature, such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil or any buildup of metallic particles
should be kept away from the USB and micro USB
plugs and port.
u
Always unplug the USB cable from the power supply
when there is no tool attached to it.
This tool has five LEDs and when in use these perform a dual
function for indicating speed and state of charge.
If the unit is between 60%-100% charged then all indicators
will illuminate green. If the unit is between 20%-60% charged
then the first LED will illuminate orange and if less than 20%
charged, the first LED will illuminate red.
See table below for details:
Charger LED Indicator
Charging One Green LED
Charging Two Green LEDs
Charging Three Green LEDs
Charging Four Green LEDs
Fully Charged Five Green LEDs
Hot/Cold Pack delay* Five Orange LEDs
*Orange charge indicator LEDs will be illuminated during this
operation. Once the battery pack has reached an appropriate
temperature, the orange LEDs will turn off and the tool will
resume the normal charging procedure.
Assembly and adjustments
@
Warning! To reduce the risk of serious personal
injury, turn unit off and lock off the tool before
making any adjustments or removing/installing
attachments or accessories. An accidental
start-up can cause injury.
Spindle lock button (Fig.B)
@
Warning! Turn tool off before changing
accessories.
u
To lock the spindle (5) for changing accessories, press
and hold the spindle lock button (6), the spindle (5) will
lock in position allowing you to install or remove the
accessories as directed in this manual.
u
To unlock the spindle (5), release the spindle lock button
(6).
Changing Accessories (Fig. C)
@
Warning! Do not use accessories with a mandrel
length exceeding 1” (25 mm). Ensure that the
exposed mandrel length is no more than 13 mm
after inserting accessory into collet.
@
Warning! Use only accessories less than 25mm
diameter and rated at 30,000 RPM or greater
Accessories are held in place by a collet (7) and collet nut (8)
as shown in Fig. C.
To Insert an Accessory
u
Turn tool off and allow it to come to a complete stop.
u
Press and hold the spindle lock button (6) and grasp the
collet nut ( 8 ) .
u
Turn the collet nut (8) counterclockwise until it is loose.
u
Insert the accessory mandrel into the collet (7) to the full
depth of the gripping jaws of the collet and at least half of
the full mandrel length.