Black Box S-COS/2 страница 7 Скачать руководство пользователя

Страница: 7 / 20

SERIAL CODE OPERATED SWITCH S-COS/2

1. Specifications

Interface —

RS232/V.24, full duplex, asynchronous

Connectors —

(3) DB25 female

Coding —

5 to 8 bit, asynchronous

Controls —

External —

(2) toggle switches (modes and manual override)

Internal —

Baud rate and format
DTE/DCE configuration switch for each port
Auto Timeout
Arming Character

Indicators —

(3) LEDs: Channel A, Channel B, and SWITCH TIME MODE

Addressing —

Two-digit code:

First digit is switch-selectable, initiates Switch Time Mode—factory

setting is EOT (Ctrl D, Hex 04)

Second digit assigns channel; Hex 31H-32H locks out the other

channel

No port is selected in the Switch Time mode

Data Rate —

75, 300, 600, 1200, 2400, 4800, 9600, 19,200 bps

Power —

115 VAC, 60Hz, 11 watts

Enclosure —

High-impact plastic

Humidity —

15% to 95% noncondensing

Temperature —

Operating — 32 to 122°F (0 to 50°C)
Storage — -4 to +158°F (-20 to +70°C)

Size —

2.25"H x 8.75"W x 11.25"D (5.7 cm x 22.2 x 28.6 )

Weight —

2.6 lb. (1.2 kg)

Circuits Supported

Pin

Name

Description

Chassis Ground, wired straight through

DTE/DCE switched for each channel

DTE/DCE switched selectable for each channel

RTS

Switch-selected to be pulled up or tied to pin 5

CTS

Switch-selected to be pulled up or tied to pin 4

DSR

DTE/DCE switched for each channel

Signal return, wired straight through

DCD

Received-line signal detector, switch-selected to be pulled up or not to be
pulled up

DTR

DET/DCE switch selectable for each channel

Pins 6 and 20 (control in and control out) are switched by the S-COS/2.
Pin 4 or 8 can be selected for control in or control out.

Содержание S-COS/2




















Результаты поиска

Содержание S-COS/2

Отзывы:

Похожие инструкции для S-COS/2

Бренды по названию

Популярные бренды

Black Box S-COS/2, Руководство пользователя

Результаты поиска

Содержание S-COS/2

Отзывы:

Похожие инструкции для S-COS/2

Бренды по названию

Популярные бренды