Black Box LE2101A-BT-R2 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 236

background image

71

TERMINAL SERVERS

4.11 Configuring SLIP Ports

The Terminal Server can be used to connect SLIP devices to an IP network.
The SLIP (Serial Link Internet Protocol) protocol is a simple implementation
of the IP protocol over Asynchronous links. The SLIP device can be a PC,
workstation, router, or any other device connected through a serial port to
the Terminal Server.

Any SLIP device must be assigned a unique IP address which must be

part of the same subnet to which the Terminal Server is connected.

The following example shows a sample configuration of a port which will

be used for a SLIP connection.

1 Local> DEFINE PORT 2 AUTOBAUD DISABLED SPEED 19200

2 Local> DEFINE PORT 2 DEDICATED SLIP

3 Local> DEFINE PORT 2 SLIP ENABLED

4 Local> DEFINE PORT 2 FLOW DISABLED

5 Local> DEFINE PORT 2 SLIP HOST 111.122.133.144

6 Local> DEFINE PORT 2 USERNAME “SLIP 2”

Figure 4-20. Configuring a Port for a SLIP Connection.

Step 1: Define the Port Characteristics

Command 1 defines a fixed speed (of 19200 baud) unlike for directly-
attached terminals.

Step 2: Define port as Dedicated SLIP and Enable it

Statement 2 specifies that the port will be attached automatically as a SLIP
host when the user logs on to the Terminal Server. DEDICATED prevents
the user from using the port as a terminal port and negates the need for any
character-mode communication—except the user name and password (if
needed). This simplifies the script required to connect the SLIP device to
the Terminal Server.

Statement 3 enables the port to work in SLIP mode. To enter SLIP mode,

the user issues a “CONNECT SLIP” command or uses the Dedicate definition
as in statement 2. After starting the SLIP mode, the Terminal Server will
expect only SLIP frames from the attached device.

«
...
69
70
71
72
73
...
»

Содержание LE2101A-BT-R2













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LE2101A-BT-R2

Бренд: IBM Страницы: 214

ML-2010 - B/W Laser Printer

Бренд: Samsung Страницы: 25

SBXL52 - Server Compute Blade

Бренд: Intel Страницы: 126

Portbase PB-3010

Бренд: SystemBase Страницы: 45

Бренд: Axis Страницы: 66

Бренд: X-media Страницы: 10

SuperServer 6019P-WT

Бренд: Supermicro Страницы: 133

Бренд: Olive Страницы: 103

SuperServer 1019D-FRN8TP

Бренд: Supermicro Страницы: 126

Бренд: Sun Microsystems Страницы: 121

Бренд: DataCard Страницы: 2

IP-DECT SERVER 400

Бренд: SpectraLink Страницы: 221

8-BAY RACKMOUNT NAS

Бренд: Seagate Страницы: 20

BlackArmor NAS 420

Бренд: Seagate Страницы: 64

Бренд: Alfresco Страницы: 49

Бренд: Planet Страницы: 125

Бренд: Blonder tongue Страницы: 20

Бренд: FreeNAS Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды