background image

A/B SWITCH WITH REMOTE INTERFACE 

Page 10 of 22 

7. Console Commands

 

 
The following commands are available from the RS232 console port or from the Ethernet network port on models of 
the A/B Switch that support these remote control interfaces.  All commands are case insensitive, although several 
parameters are case sensitive (read/write community names and web and telnet passwords).  GET, SET, and 
SYSTEM can all be abbreviated by the first letter of the command.  This allows shorthand entry of switching 
commands. Each available command is shown along with an example of a typical response. 
 
 
GET ALL 
 
Displays all parameters and settings.  An example output is shown here. 
 

System Status: B  
IP Address: 192.168.1.39  
MAC Address: 00 06 57 00 01 02  
Subnet Mask: 255.255.255.0  
Gateway IP Address: 192.168.1.1  
PING Reply: Enabled 
SNMP Enable: Enabled 
Read Community Name: public  
Write Community Name: private  
Web Enable: Enabled  
Web Password: mctech  
Web Timeout: 300  
Web Port: 80  
Telnet Enable: Enabled  
Telnet Password: dataman  
Telnet Timeout: 80  
Telnet Port: 23  
Monitor IP Address: 192.168.1.113  
Monitor MAC Address: 00 00 00 00 00 00  
Monitor Interval: 10  
Monitor Fail Count: 5  
Monitor Ok Count: 5  
Authentication Trap: Disabled  
Alert Type: TRAP  
D1000: 2.9N JUL 2010, d1000 Rev B 
ADMIN IP Addresses: 
SNMP Managers:  

1: 192.168.1.113 

2: 192.168.1.115 

3: 192.168.1.149 

 
 

GET VERSION 
 
Displays the software revision of the system. 
 

D1000: 2.9h MAY 2008, d1000 Rev B 

 
 
GET SYSTEM  
 
Displays the system status.  This is the same as the status returned by the SNMP variable d1000SwitchControl.  It 
will report “A” if the switch is in position A, and “B” if the switch is in position B. 

Содержание 12 VDC load























Отзывы: