•
CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced by an authorized
service center unless otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by authorized service center. Do
not use tool if switch does not turn it on and off.
•
DO NOT OPERATE
portable electric tools near flammable liquids or in
gaseous or explosive atmospheres. Certain components in these tools
normally spark, and the sparks might ignite fumes.
•
OUTDOOR USE EXTENSION CORDS.
When tool is used outdoors, use
only extension cords intended for use outdoors and so marked.
• EXTENSION CORDS.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. The following table
shows the correct size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gage. The smaller the gage
number, the heavier the cord.
SAFETY GUIDELINES / DEFINITIONS
DANGER:
Indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR
ALL APPLIANCES
READ ALL INSTRUCTIONS
WARNING:
Read all instructions before operating product. Failure to
follow all instructions listed below may result in electric shock, fire and/or
serious injury.
•
AVOID DANGEROUS ENVIRONMENTS
Don’t use appliances in damp or
wet locations. Don’t use appliances in the rain.
•
KEEP CHILDREN AWAY.
All visitors should be kept at a distance from
work area.
•
STORE IDLE APPLIANCES INDOORS.
When not in use, appliances should
be stored indoors in dry, and high or locked-up place – out of reach
of children.
•
USE RIGHT APPLIANCE.
Do not use the appliance for any job except that
for which it is intended.
•
DRESS PROPERLY.
Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and substantial, non-skid footwear
are recommended when working outdoors. Wear protective hair covering
to contain long hair.
•
USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT.
Use safety
goggles or safety glasses with side shields, complying with applicable
safety standards and, when needed, a face shield. Also use face or dust
mask if operation is dusty. This applies to all persons in the work area. Also
use a hard hat, hearing protection, gloves, safety shoes and dust collection
systems when specified or required. Safety glasses or the like are available
at extra cost at your local dealer or Black & Decker Service Center.
•
DON’T ABUSE CORD.
Never carry appliance by cord or yank it to
disconnect from receptacle. Keep cord from heat, oil, and sharp edges.
•
DON’T OVERREACH.
Keep proper footing and balance at all times.
•
DISCONNECT APPLIANCES.
Disconnect the appliance from the power
supply when not in use, before servicing, and when changing accessories
such as blades and the like.
•
AVOID UNINTENTIONAL STARTING.
Don’t carry plugged-in appliance
with finger on switch. Be sure switch is off when plugging in.
•
GROUND FAULT CIRCUIT INTERRUPTER (GFCI)
protection should be
provided on the circuits or outlets to be used. Receptacles are available
having built in GFCI protection and may be used for this measure of safety.
•
USE OF ACCESSORIES AND ATTACHMENTS.
The use of any accessory or
attachment not recommended for use with this appliance could be
hazardous. Note: Refer to the accessory section of this manual for
further details.
•
STAY ALERT.
Watch what you are doing. Use common sense. Do not
operate tool when you are tired.
2
1
Minimum Gage for Cord Sets
Volts
Total Length of Cord in Feet
120V
0-25
26-50
51-100
101-150
(0-7,6m) (7,6-15,2m)
(15,2-30,4m)
(30,4-45,7m)
240V
0-50
51-100
101-200
201-300
(0-15,2m) (15,2-30,4m) (30,4-60,9m)
(60,9-91,4m)
Ampere Rating
More
Not more
American Wire Gage
Than
Than
0 -
6
18
16
16
14
6 -
10
18
16
14
12
10 -
12
16
16
14
12
12 -
16
14
12
Not Recommended
BB7B_Manual EN_082406 8/24/06 10:14 AM Page 1