Black & Decker RS890, Оригинальное руководство пользователя

Страница: 6 / 84

6
ENGLISH (Original instructions)
Autoselect (fig. B)
The Autoselect feature allow you to set the optimum speed of
the tool dependant on the material you are cutting.
u
Slide the Autoselect switch (3) to the top position for cut-
ting sheet metal.
u
Slide the Autoselect switch (3) to the middle position for
cutting plastic.
u
Slide the Autoselect switch (3) to the bottom position for
cutting wood and metal tubing.
Sawing (fig. C)
u
If possible, always hold the tool with both hands using the
main handle (7) and secondary handle (8).
u
Let the blade run freely for a few seconds before starting
the cut.
u
Apply only a gentle pressure to the tool while performing
the cut.
u
Keep the shoe/branch steady (5) pressed firmly against
the workpiece.
Pruning branches (fig. D & E)
u
If possible, always hold the tool with both hands using the
main handle (7) and secondary handle (8).
u
Rotate the branch steady (5) till it clicks into place.
u
Let the blade run freely for a few seconds before starting
the cut.
u
Position the saw so that the blade is above the branch and
the branch steady (6) is below the branch.
u
Apply only a gentle pressure to the tool while performing
the cut.
u
For proper cutting, the branch being cut should be in con-
tact with both sides of the pruning shoe. The cut should
be square to the branch, and not made at an angle. If
required a rotating action could be used to further improve
the speed of the pruning cut.
Warning! The branch steady (6) is not a handle and should
never be used as a handle. Always hold the tool using the
main handle (7) and the secondary handle (8 or 9).
Operating in jigsaw mode (fig. F)
u
If possible, always hold the tool with both hands using the
main handle (7) and secondary handle (9).
u
Rotate the branch steady (5) till it clicks into place.
u
Fit the required blade.
Hints for optimum use
u
Do not exert too much pressure on the tool.
u
Regularly check the condition of accessories. Replace
when necessary.
Sawing wood
u
Clamp the workpiece securely and remove all nails and
metal objects.
u
When splintering is to be minimised, e.g. when cutting
laminates, clamp a piece of scrap wood or hardboard to
both sides of the workpiece and saw through this sand-
wich.
Sawing metal
u
Be aware that sawing metal takes much more time than
sawing wood.
u
Use a saw blade suitable for sawing metal.
u
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut through
this sandwich.
u
Spread a film of oil along the intended line of cut.
Cutting branches
u
Cut downward and away from your body.
u
Make the cut close to the main branch or tree body.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u
Or run the battery down completely if it is integral and then
switch off.
u
Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
plug.
u
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.