Black & Decker PW 1800 SPL, Инструкция по эксплуатации, Страница: 22 / 28

22 • ENGLISH
Warning! Safety signs. Comply with the instructions
provided by the safety signs ted to the appliance. Check
that they are present and legible; otherwise, replacements
in the original positions.
TECHNICAL INFORMATION
ENVISAGED USE
This appliance has been designed for individual use for the
cleaning of vehicles, machines, boats, masonry, etc, to remove
stubborn dirt using clean water and biodegradable chemical
detergents.
Vehicle enginesmay be washed only if the dirty water is
disposed of as per regulations in force.
f
Intake water temperature: See data plate on
the appliance.
f
Intake water pressure: Below 10 bar.
f
Operating ambient temperature: Above 0 °C.
The machine complies with the IEC.
OPERATOR
The symbol on the front cover identifies the appliance’s
intended operator (professional or non-professional).
MAIN COMPONENTS (Fig. A)
The machine is delivered partially disassembled
in a carton.
1. Lance with adjustable spray nozzle
2. Rotary spray nozzle
3. Gun with safety catch
4. Power supply cable with plug
(on models with this feature)
5. High pressure hose
6. Detergent tank (on models with this feature)
7. Nozzle cleaning tool
8. Rotating nozzle kit
9. Handle
10. Hose reel
Caution! Safety devices:
Do not tamper with or adjust the safety valve setting.
f
Safety valve and pressure limiting valve:
The safety valve is also a pressure limiting valve.
When the gun trigger is released, the valve opens
and the water recirculates through the pump inlet or is
discharged onto the ground.
f
Thermostat valve (where fitted)
If the water temperature exceeds the temperature
set by the manufacturer, the thermostat valve
discharges the hot water and draws in an amount of
cold water equal to the amount of water discharged,
until the correct temperature is restored.
f
Safety catch (11): prevents accidental spraying of water.
INSTALLATION (Fig. B)
ASSEMBLY
Caution! All installation and assembly operations must
be performed with the appliance disconnected from the
mains power supply.
The assembly sequence is illustrated in Fig. B.
Assembling the rotating nozzle
(For models with this feature)
The rotating nozzle kit delivers greater washing power.
Use of the rotating nozzle may cause of reduction in pressure
of 25% compared to the pressure obtained with the adjustable
nozzle. However, the rotating nozzle kit delivers greater
washing power due to the rotation of the water jet.
Electrical connection
Caution! Check that the electrical supply voltage and
frequency (V/Hz) correspond to those on the appliance
data plate (Fig. B8) The appliance should only be connected
to a mains power supply equipped with an adequate earth
connection and a d erential security breaker (30mA) to cut
off the electricity supply in the instance of a short circuit.
Use of extension cables: Use cables featuring “IPX5”
protection level. The cross-section of the extension cable
should be proportionate to its length; the longer it is, the
greater its cross-section should be.
Water supply connection
Caution! Only clean or filtered water should be used for
intake. The delivery of the water intake tap should be equal
to that of pump capacity. Place the appliance as close to
the water supply system as possible.
Connection points:
Water outlet (OUTLET)
Water inlet with filter (INLET)
Connection to the mains water supply
The appliance can be connected directly to the mains
drinking water supply only if the supply hose is fitted with a
backflow preventer valve as per current regulations in force.
Make sure that the hose is at least Ø 13mm and that it is
reinforced.
ADJUSTMENT INFORMATION (Fig. C)
f
Adjusting the spray nozzle (for models with this
feature) Water flow is adjusted by regulating the
nozzle (12).
f
Adjusting the detergent (on models with this feature)
Detergent flow is adjusted using the regulator.
f
Adjusting the detergent pressure set the adjustable
nozzle (12) on “ ” to deliver detergent at the correct
pressure (on models with this feature).