6
ENGLISH
These are:
• Injuries caused by touching any rotating/moving parts.
• Injuries caused when changing any parts, blades or
accessories.
• Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
• Impairment of hearing.
• Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Labels on tool
The following symbols are shown on the tool:
Warning!
To reduce the risk of injury, the user must
read the instruction manual.
Position of date barcode
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX JN
Year of manufacturing
Electrical safety
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
• If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black and Decker Service
Centre in order to avoid a hazard.
Using an extension cable
If it is necessary to use an extension cable, please used an
approved extension cable that fits the tool’s power input
specifications (please refer to the technical data). The
minimum cross-sectional area of the conducting wire is 1.5
sq. mm. Cables should be untangled before reeling up.
Features
This tool includes some or all of the following features.
a. Side Handle
b. Switch
c. Barrel cover
d. Tool sleeve
e. Lube oil-injection inlet
Assembly and adjustment
Warning!
To reduce the risk of injury, turn
unit off and disconnect machine from power
source
before installing and removing
accessories, before adjusting or changing set-ups or when
making repairs. Be sure the trigger switch is in the OFF
position. An accidental start-up can cause injury.
Inserting and removing SDS Max accessories (fig. 1)
This tool uses SDS Max accessories (refer to the inset in
figure 1 for a cross-section of an SDS Max bit shank). We
recommend to use professional accessories only.
1. Clean and grease the bit shank.
2. Insert the bit shank into the bit holder/tool sleeve (d).
3. Push the bit down and turn it slightly until it fits into the
slots.
4. Pull on the bit to check if it is properly locked. The
hammering function requires the bit to be able to move
axially several centimetres when locked in the tool
holder.
5. To remove a bit pull back the tool holder/locking sleeve
(d) and pull out the bit.
Warning:
Always wear gloves when you
change accessories. The exposed metal parts
on the tool and accessory may become
extremly hot during operation.
Fitting the side handle (fig. 1)
The side handle (a) can be fitted to suit both RH- and
LH-users.
Warning:
Do not use the tool without the side
handle properly assembled.
1. Loosen the side handle.
2. For RH-users: Slide the side handle clamp over the
collar behind the tool holder, handle at the left. For
LH-users: Slide the side handle clamp over the collar
behind the tool holder, handle at the right.
3. Rotate the side handle to the desired position and
tighten the handle.
Operation instructions for use
Warning:
Содержание PRO Series
