9
ENGLISH
(Original instructions)
blade, in the direction of motion gives the best cutting.
Warning!
Do not cut stems greater than 19mm. Use the
trimmer only for cutting normal shrubbery around houses and
buildings.
Level hedges (Fig. I)
u
To obtain exceptionally level hedges a piece of string can
be stretched along the length of the hedge as a guide.
Side trimming hedges (Fig. J)
u
Hold the trimmer as shown and begin at the bottom and
sweep up.
POWERCOMMAND (Fig.K)
If you encounter a jam, depress the POWERCOMMAND
button (4) shown in figure K. The blades will move back and
forth in a slower, more forceful rhythm to help cut through dif-
ficult branches. Release the button to return to normal hedge
trimming usage.
Note:
Once the button is released, the blades will immediately
return to full speed.
Note:
The blades will stop when the button is held for 15 sec-
onds. To reengage the POWERCOMMAND feature, release
the button and depress it again. DO NOT continuously hold
the POWERCOMMAND button during normal hedge trimming.
Saw blade (Fig.L)
For branches too large for the blade ( 7 ) to cut, use the saw
blade (8 ). Position the saw blade as close to the bottom of the
branch as possible. Place the saw blade shoe ( 9 ) against the
branch. Turn the hedge trimmer on as described above, allow-
ing the tool to work at its own pace until the branch is fully cut.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning!
Before performing any maintenance on corded/
cordless power tools:
u
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u
Or run the battery down completely if it is integral and then
switch off.
u
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u
Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u
After use, carefully clean the blades. After cleaning, apply
a film of light machine oil to prevent the blades from rus -
ing.
T
he cutting blades are made from high quality, hardened steel
and with normal usage, they will not require resharpening.
However, if you accidentally hit a wire fence, stones, glass or
other hard objects, you may put a nick in the blade.
There is no need to remove this nick as long as it does not
interfere with the movement of the blade. If it does interfere,
remove the battery and use a fine toothed file or sharpenin
g
stone to remove the nick.
If you drop the trimmer, carefully inspect it for damage. If the
blade is bent, housing cracked, or handles broken or if you
see any other condition that may affect the trimmer’s opera-
tion contact your local BLACK+DECKER Service Center for
repairs before putting it back into use. Fertilizers and other
garden chemicals contain agents which greatly accelerate
the corrosion of metals. Do not store the unit on or adjacent
to fertilizers or chemicals. With the battery removed, use only
mild soap and a damp cloth to clean the unit. Never let any
liquid get inside the unit; never immerse any part of the unit
into a liquid. Prevent the blades from rusting by applying a film
of light machine oil after cleaning.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted
u
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
plug.
u
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Troubleshooting
Problem
Possible Cause
Possible Solution
Slow running,
noisy or hot
blades.
Dry, corroded blades.
Lubricate blades.
Blade or blade sup-
port bent.
Straighten blade or blade support.
Bent or damaged
teeth.
Straighten teeth.
Loose blade bolts.
Tighten blade bolts.
Unit will not
start.
Battery not installed
properly.
Check battery installation.
Battery not charged.
Check battery charging require-
ments.
Lock off not fully
operated.
Check lock off is fully depressed
prior to moving main trigger.
