Black & Decker FSM1625, Руководство пользователя

Страница: 7 / 16

7
ENGLISH (Original instructions)
water reservoir will glow blue.
u
To switch the appliance off, press the ON/OFF button (1).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (8) with the handle (4) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Caution! Always empty the steam mop after use.
Autoselect
TM
Technology
This steam mop is fitted with an Autoselect
TM
dial (2) which
shows various cleaning applications. They are used to select
the correct operating mode for your particular cleaning opera-
tion.
Using the Autoselect
TM
dial (2), choose from one of the follow-
ing applications:
Wood/Laminate
Stone/Marble
Tiles/Vinyl
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop.
Hints for optimum use
General
Caution! Never use the steam mop without first attaching a
cleaning pad.
u
During use you can use the cable mamagement clip (11)
to keep your cable out of the way of the work area..
u
Always vacuum or sweep the floor before using the steam
mop.
u
The easiest way to use the machine is to tilt the handle to
a 45˚ angle and clean slowly, covering a small area at a
time.
u
Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum floors, you
can pre-treat with a mild detergent and some water before
using the steam mop.
Steam cleaning
u
Place a cleaning pad (6 or 7) on the floor with the ‘hook &
loop’ side facing up.
u
Raise the steam mop off the resting mat (8) and lightly
press it down onto the cleaning pad (6 or 7).
u
Place the steam mop on the resting mat.
u
Connect the steam mop to the mains.
u
Turn the Autoselect
TM
dial (2) to the required setting.
u
Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
u
Pulling the handle (4) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head.
u
It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitised/cleaned.
u
Push and pull the steam mop slowly across the floor to
thoroughly steam clean each section.
Note: During use you may turn off the steam pump by return-
ing the handle to the upright position, this convenient feature
will allow you to place the steam mop on the resting mat for
a short time so that you may move items of furniture, then
continue cleaning without the need to switch the appliance off.
u
When you have finished using the steam mop, return the
handle (4) to the upright position and turn it ‘OFF’, place it
on the resting mat (8) and wait until the steam mop cools
down. (approximately five minutes)
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean,
return the handle (4) to the upright position and turn the steam
mop ‘OFF’. Unplug the unit from the electrical wall outlet,
remove and refill the water tank (3).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (8) with the handle (4) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Carpet refreshing
u
Place a cleaning pad (6 or 7) on the floor with the ‘hook &
loop’ side facing up.
u
Raise the steam mop off the resting mat (8) and lightly
press it down onto the cleaning pad (6 or 7).
u
Place the carpet glider (12) on the floor.
u
Lightly press the steam mop down onto the carpet glider
(12) until it clicks into place.
u
Place the steam mop on the resting mat. (8)
u
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
u
Turn the Autoselect
TM
dial (2) to the Wood/Laminate set -
ting.
u
Pulling the handle (4) back will activate the steam pump.
After a few seconds steam will start to come out of the