Additional Safety Instructions For Australia And New
Zealand
a) Young children and the infirm.
This appliance is not intended
for use by young children or infirm persons without supervision.
Young children should be supervised to ensure that they do not
play with this appliance.
b) Replacement of the supply cord.
If the supply cord is
damaged, it must be replaced by the manufacturer or an
authorised DEWALT Service Centre in order to avoid a hazard.
Electrical safety
This tool is double insulated; therefore no earth wire is required.
Always check that the power supply corresponds to the voltage
on the rating plate.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Keyless chuck
6. Depth stop
7. Side handle
Assembly
Warning!
Make sure that the tool is switched off and unplugged.
Fitting the side handle and depth stop (fig. B)
• Turn the grip (7) counterclockwise until you can slide the side
handle (8) onto the front of the tool as shown.
• Rotate the side handle into the desired position.
• Insert the depth stop (6) into the mounting hole
as shown.
• Set the depth stop to the desired position. The
maximum drilling depth is equal to the distance
between the tip of the drill bit and the front end of the depth stop.
• Tighten the side handle by turning the grip clockwise.
Fitting a drill bit or screwdriver bit
Keyless chuck (fig. C)
• Open the chuck by turning the front part (10) with one hand
while holding the rear part (9) with the other.
• Insert the bit (11) shaft into the chuck and firmly tighten the
chuck.
Removing and refitting the chuck
Keyless chuck (fig. D)
• Open the chuck as far as possible.
• Remove the chuck retaining screw, located in the front part of
the chuck, by turning it clockwise using a screwdriver.
• Tighten an Allen key (12) into the chuck and strike it with a
hammer as shown.
• Remove the Allen key.
• Remove the chuck by turning it counterclockwise.
• To refit the chuck, screw it onto the spindle and secure it with
the chuck retaining screw.
Warning!
Always make sure that the chuck is securely fitted.
Use
Warning!
Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Selecting the direction of rotation
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
• To select forward rotation, push the forward/reverse slider
(3) to the left.
• To select reverse rotation, push the forward/reverse slider to
the right.
Warning!
Never change the direction of rotation while the motor
is running.
Selecting the drilling mode
• For drilling in masonry, set the drilling mode selector (4) to
the position.
• For drilling in other materials and for screwdriving, set the
drilling mode selector (4) to the position.
Switching on and off
• To switch the tool on, press the variable speed switch (1).
The tool speed depends on how far you press the switch. As a
general rule, use low speeds for large diameter drill bits and high
speeds for smaller diameter drill bits.
• For continuous operation, press the lock-on button (2) and
release the variable speed switch. This option is available only
at full speed.
• To switch the tool off, release the variable speed switch. To
switch the tool off when in continuous operation, press the
variable speed switch once more and release it.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to high
quality standards and designed to enhance the performance of
your tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Regularly clean the ventilation slots with a clean, dry paint
brush. To clean the tool, use only mild soap and a damp cloth.
Never let any liquid get inside the tool and never immerse any
part of the tool into liquid.
Protecting the environment
Black & Decker provides a facility for recycling Black & Decker
products once they have reached the end of their working life.
This service is provided free of charge. To take advantage of
this service please return your product to any authorised repair
agent who will collect them on our behalf. You can check the
location of your nearest authorised repair agent by contacting
your local Black & Decker office at the address indicated in this
manual. Alternatively, a list of authorised Black & Decker repair
agents and full details of our after-sales service and contacts are
available on the Internet at: www.2helpU.com.
Содержание FS6000-XE
Страница 1: ...Australia New Zealand ...
Страница 2: ...8 6 7 Fig C Fig D Fig B 11 10 9 12 ...
