Black & Decker EVO143, Оригинальное руководство пользователя

Страница: 10 / 32

10
ENGLISH (Original instructions)
(15) down and pull the saw blade from the holder.
Fitting and removing sanding sheets
(fig. G)
The sanding head uses pre-cut sanding sheets.
u
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
u
Before fitting a new sheet, remove the two additional
diamond tips (19).
u
To fit a sanding sheet, line it up with the sanding base (18)
as shown.
u
Press the sheet firmly and evenly onto the sanding base,
making sure that the holes in the sheet coincide with the
holes in the base.
u
To remove the sheet, pull it off the sanding pad.
Warning! Never use the sanding head without a sanding
sheet or accessory in place.
Replacing the diamond sanding tip (fig. H)
Sanding sheets are supplied with two replacement diamond
tips. The diamond tip can be reversed when worn. When both
sides are worn, replace the diamond tip.
u
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
u
To reverse the tip, remove it, turn it 180° and press it back
onto the base.
u
To replace the tip, pull the old tip off the base and press a
new one onto the base.
Warning! When removing the tip from the pad, be careful not
to pull the pad off the sanding base.
Fitting and removing the dust extraction adaptor
(fig. I)
u
Line up the dust extraction adaptor (20) with the sanding
head (17) as shown.
u
Press the adaptor firmly and evenly in to the sanding
base.
u
Connect a vacuum cleaner to the dust extraction adaptor.
u
To remove, pull the dust extraction adaptor (20) out of the
sanding head (17).
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Charging the battery (fig. C)
The battery needs to be charged before first use and whenev -
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u
To charge the battery (5), insert it into the charger (10).
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
u
Plug in the charger and switch on at the mains.
The charging indicator (11) will flash green continuously
(slowly).
The charge is complete when the charging indicator (11)
lights green continuously. The charger and the battery can be
left connected indefinitely with the LED illuminated. The LED
will change to flashing green (charging) state as the charger
occasionally tops off the battery charge. The charging indica-
tor (11) will be lit as long as the battery is connected to the
plugged-in charger.
u
Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the charg-
ing indicator (11) will flash red at a fast rate. Proceed as
follows:
u
Re-insert the battery (5).
u
If the charging indicators continues flashing red at a fast
rate, use a different battery to determine if the charging
process works properly.
u
If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
u
If the new battery gives the same indication as the original
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Selecting the torque or drill position (fig. D)
This tool is fitted with a collar to set the torque for tightening