31
TIẾNG VIỆT
Không để bộ sạc tiếp xúc với nước.
Không mở bộ sạc ra.
Không chọc que vào bộ sạc.
Thiết bị/pin phải được đặt ở nơi thông thoáng
khi sạc.
An toàn điện
Ký hiệu trên bộ sạc
Đọc kỹ tài liệu hướng dẫn này trước khi sử
dụng thiết bị.
Do dụng cụ này được cách điện kép nên
không cần dây nối đất. Luôn kiểm tra
nguồn điện có tương ứng với điện áp trên
biển thông số định mức hay không.
Đế sạc chỉ được thiết kế để sử dụng trong
nhà.
Ký hiệu trên thiết bị
Trên thiết bị có các ký hiệu sau cùng với mã ngày
Đọc kỹ tài liệu hướng dẫn này trước khi
sử dụng thiết bị
Chỉ sử dụng cùng với bộ sạc S010Q 23
Tính năng
Dụng cụ này gồm một số hoặc tất cả những tính
năng sau.
1. Công tắc bật/tắt
2. Vòi hút
3. Đầu hút dẹt kéo dài
4. Chổi đẩy
5. Công tắc bật/tắt trên tay cầm.
5A. Điều khiển chổi than
6. Tay cầm
7. Đế sạc
8. Bệ đỡ
8a. Nút tháo lắp bệ đỡ
Cách sử dụng
Bật và tắt (Hình A)
Để bật, ấn vào công tắc bật/tắt (1) trên tay cầm
của Máy hút bụi
®
hoặc trên tay cầm của bệ đỡ
(5).
Ấn lại vào nút (1 hoặc 5) và thiết bị sẽ chuyển
sang chế độ TĂNG TỐC.
Để tắt máy, ấn vào công tắc bật/tắt (1) hoặc (5).
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$
The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+
Read all of this manual carefully before
using the appliance
S010Q 23
Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$
The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+
Read all of this manual carefully before
using the appliance
S010Q 23
Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$
The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+
Read all of this manual carefully before
using the appliance
S010Q 23
Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$
The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+
Read all of this manual carefully before
using the appliance
S010Q 23
Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
7
Even with the application of the relevant
safety regulations and the implementa-
tion of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any
rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your
tool (example:- working with wood,
especially oak, beech and MDF.)
Chargers
Your charger has been designed for a
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace the
charger unit with a regular mains plug.
Use your BLACK+DECKER charger
only to charge the battery in the
appliance with which it was supplied.
Other batteries could burst, causing
personal injury and damage.
Never attempt to charge non-
rechargeable batteries.
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
Do not open the charger.
Do not probe the charger.
The appliance/battery must be
placed in a well ventilated area when
charging.
Electrical safety
Symbols on the charger
Read all of this manual carefully before using the
appliance.
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
$
The charging base is intended for indoor use only.
Labels on appliance
The following symbols appear on this appliance along with the
date code
+
Read all of this manual carefully before
using the appliance
S010Q 23
Only use with charger S010Q 23
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Handle
3. Nozzle
4. Pull out crevice tool
5. LED charging indicator
6. Dust bowl
7. Push in brush
8. Floor extension release clip
9. Floor extension tube
10. Floor head release clip
11. Flip down brush
12. Floor head
13. Wall bracket
14. Charger
15. Charging port
Use
Switching on and off (Fig. A)
Press the button to turn, on the unit operates in slow
speed, low power mode, conserving the battery life.
Press the button again, and the unit goes to a BOOST
mode.
Pressing the button again will turn the product off.
Using the pull out crevice tool (Fig. B,C)
required for dusting and upholstery cleaning.
Sử dụng đầu hút dẹt kéo dài
(Hình B, C)
Kéo đầu hút dẹt (3) ra như minh họa trong hình
C cho đến khi đầu hút khớp vào đúng vị trí. Sau
đó có thể lắp chổi đẩy (4) vào nếu cần để hút
bụi và vệ sinh ghế.
Để thu lại đầu hút dẹt (3), ấn nút tháo lắp đầu
hút dẹt (3a) để nó trở về vị trí ban đầu (Hình B).
Lắp tay cầm vào bệ đỡ chính
(Hình D, E)
Trượt tay cầm (6) vào bệ đỡ chính (8) như
minh họa trong hình D.
Cố định bằng vít (17) như minh họa trong hình
E.
Lắp Máy hút bụi
®
vào Bệ đỡ
(Hình F, G, H)
Đầu tiên, trượt Máy hút bụi
®
, vòi hút vào bệ đỡ
(8) cho đến khi nghe thấy tiếng cách như minh
họa trong hình F.
Để tháo Máy hút bụi
®
khỏi bệ đỡ, ấn vào nút
tháo lắp bệ đỡ (8a) rồi lấy ra.
Bây giờ, có thể vận hành thiết bị thông qua
nút bật/tắt (5) trên tay cầm (6) cùng với chế độ
‘TĂNG TỐC’ như minh họa trong hình H. Điều
này cũng cho phép bạn sử dụng thanh chải
thông qua việc điều khiển ‘sử dụng chổi’ (5A).
Tháo và lấy tóc ra khỏi thanh chải
(Hình I, J)
Để tháo bộ phận thanh chải (9) ra khỏi đầu hút
sàn (10), ấn nút tháo lắp (11) như minh họa
trong hình I.
Sau đó, có thể tháo thanh chải (12). Bạn cũng
có thể tháo rời hai đầu của thanh chải để vệ
sinh tóc hoặc mảnh vụn khác trên các chổi có
thể tích tụ trong quá trình sử dụng (Hình J).
Sạc (Hình K, L)
Đặt thiết bị lên đế sạc (7) như minh họa trong
hình K.
Cắm cổng sạc (7) vào ổ điện.
Bật ổ cắm điện. Đèn LED báo sạc (B) sẽ sáng
(Hình L).
Содержание Dustbuster CS1830
