Black & Decker CS36BS, Оригинальное руководство пользователя

Страница: 6 / 68

6
ENGLISH (Original instructions)
Selecting the direction of rotation (fig. C)
For tightening screws, use forward rotation.
For loosening screws or removing a jammed drill bit, use
reverse rotation.
u
To select forward rotation, push the forward/reverse slider
(2) to the forward position.
u
To select reverse rotation, push the forward/reverse slider
(2) to the rearward position.
u
To lock the tool, set the forward/reverse slider into the
centre position.
Screwdriving
u
Select forward or reverse rotation using the forward/
reverse slider (2).
u
To switch the tool on, press the on/off switch (1).
u
To switch the tool off, release the on/off switch (1).
LED light
The LED light (4) is activated automatically when the trigger
is depressed. The LED will also illuminate when the trigger is
depressed and the forward/reverse slider (2) is in the locked
off position (central position).
Hints for optimum use
Screwdriving
u
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u
Use the spindle lock to loosen very tight screws or to
firmly tighten screws.
u
Always hold the tool and screwdriver bit in a straight line
with the screw.
u
When screwing in wood, it is recommended to drill a
pilot hole with a depth equal to the length of the screw.
A pilot hole guides the screw and prevents splintering or
distortion of the wood. For the optimum size of the pilot
hole, refer to the table below.
u
When screwing in hardwood, also drill a clearance hole with
a depth equal to half the length of the screw.
For the optimum size of the clearance hole, refer to the
table below.
Screw size Pilot hole ø Pilot hole ø Clearance hole
(softwood) (hardwood)
No. 6 (3.5 mm) 2.0 mm 2.5 mm 3.6 mm
No. 8 (4 mm) 2.5 mm 3.0 mm 4.5 mm
No. 10 (5 mm) 3.0 mm 3.5 mm 5.0 mm
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER and Piranha accessories are engineered
to high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
This tool uses screwdriver bits with a 1/4" (6.35 mm)
hexagonal shank. Piranha Super-lok accessories are
designed for use with this tool.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning. Your
charger does not require any maintenance apart from regular
cleaning.
Warning! Before performing any maintenance on the tool,
switch off and unplug the tool or remove the battery from the
tool if the tool has separate battery. If the battery is integral,
run the battery completely down. Unplug the charger before
cleaning it.
u
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
u
Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com.
Technical data
CS36BS (H1)
Voltage V
DC
3.6
No-load speed min
-1
180 rpm
Hard stall torque Nm 5.84Nm
Max. torque PTI N m 5.5Nm
Bit holder mm 6.35 (1/4")
Weight kg 0.42
Battery
Voltage V 3.6
Battery type Li-Ion
Capacity Ah 1.5