Black & Decker BLB 1401, Руководство пользователя

Страница: 7 / 12

7
Features
This appliance includes some or all of the following features.
1. Hose
2. Container
3. Container release button
4. Container handle
7. On/off switch
6. Variable speed switch
5. Cord rewind button
8. Handle
9. Wheels
10. Hepa filter
11. Suction head
In addition, this appliance is supplied with some or all of the
following accessories (fig. A):
12. Telescopic wands
13. Hose handle and air flow control
14. Crevice combo brush tool
15. Upholstery brush.
Assembly
Connecting the hose (fig. A)
Insert the hose connector into the inlet of the
appliance.
Line up the hose connector tabs with the slots in the inlet.
Slide the hose further until the release buttons (18) (2
positions) click into place.
To disconnect the hose, press the release buttons (18) (2
positions) and pull out the hose.
Mounting the extension tube (fig. A)
Slide the hose nozzle (13) into the tube (12) until
it locks into place.
To remove the tube (12), grip firmly and pull the
hose nozzle (13) out of the tube.
Mounting the suction head (fig. A)
The suction head (11) allows for vacuuming on carpet and
hard surfaces (e.g. laminate and tiles).
Slide the tube (12) into the head (11) until it locks into place.
To remove the head (11), grip the head firmly and pull
the tube (12) out of the head (11).
Mounting accessories (fig. A)
The crevice tool (14) allows for vacuuming in narrow and
hard to-reach places. The brush tool (14) allows for
vacuuming on furniture, blinds, curtains, windows and stairs.
Slide the accessory onto
the hose nozzle (13) or the tube (12).
To remove an accessory, pull the accessory off.
Use
Unwinding and rewinding the cord (fig D)
The cord rewind button (5) can be operated by hand or foot.
Before use, pull the full length of cord from the back of
the appliance. Pull out till the yellow marker is visible.
Do not pull the cord further when the red marker becomes
visible.
After use, press the cord rewind button (5) to store the cord
back into place. Manually guide the cord to ensure it does
not swing back. Ensure the plug is correctly located.
Adjusting the length of the wand (fig. B)
The telescopic wand (12) is made up of two pieces.
To extend the lower tube, press the adjustment
button and slide out the second tube until it is fully extended
and clicks into place.
Adjusting the suction head (fig. A)
For vacuuming on carpets, switch the floor surface selector
into the up position.
For vacuuming on laminates, tiles, etc., switch the floor
surface selector into the down position.
Switching on and off
The on/off switch (7) can be operated by hand or foot.
To switch the appliance on, press the on/off switch (7).
To switch the appliance off, press the on/off switch (7)
again.
Adjusting the airflow (fig. E)
Slide the airflow control switch to adjust the airflow
as desired. Max and min positions are shown.
Vacuuming
When operating the appliance, make sure that the hose is
not trapped, twisted or blocked
In case of overheating, a cut-out will operate and the
appliance will automatically stop.
If the appliance stops operating, unplug the appliance and
allow it to cool for 2-3 hours.
Hint for optimum use
When vacuuming stairs, always start at the bottom and
work your way up. Position the appliance on the floor and
do the stairs until halfway. Then carry the appliance to a
stable position which is at least one stair below your
working position, and do the top half of the stairs.
Carrying the appliance (fig. C)
During use the appliance can be carried using the handle (8).
Slide the variable speed control (6) on the vacuum
body change the motor speed hence the suction.