Black & Decker BG180, Оригинальное руководство пользователя, Страница: 7 / 16

7
ENGLISH
wheels are designed for side grinding and will say
so on their instruction sheets).
Stop and disconnect machine. Use two hands
to lift up machine from two sides of bottom of
bearing housing.
Caution! Prolonged grinding will cause
most materials to become hot. Handle
them with pliers.
SWITCH
The switch is located on the front of the grinder
(Fig. A) , on the base. To turn the tool on depress
the side of the rocker switch on the right side,
marked “ON”. To turn off the grinder, depress the
left side of the rocker switch, marked “OFF”.
Changing accessories (Fig. B)
Turn off the tool and disconnect from power
supply. Use only wheels that measure 6”
(152 mm) in diameter. This tool has 1/2” (13 mm)
arbors on both sides.
Follow the steps below to remove and replace an
accessory:
1. Loosen and pull the tool rest out as far as
possible. Do not remove it.
2. Remove the three screws from the side of the
wheel cover and remove the cover.
3. Insert a flat bladed screwdriver into the slot in
the left end of the grinder’s rotor shaft. Hold
the screwdriver firmly to keep the shaft from
turning as you loosen and remove the hex nut
in the center of the grinding wheel or other
accessory.
4. Remove the wheel washer and the wheel.
5. Inspect the wheel for cracks, chips or any other
visible damage (other than normal wear) and
discard if such damage is found. Inspect the
blotters for damage. If the blotters are missing
or severely damaged, replace them with pieces
of thin cardboard or blotter paper cut in the
same shape. Never use a grinding wheel
without a blotter on each side of the wheel.
6. Install the new wheel or other accessory. Be
sure that both wheel washers are in place
(concave sides toward wheel). Use only
flanges furnished with the grinder.
7. Hold as before and tighten the nut firmly but
do not overtighten. Overtightening can crack
a grinding wheel.
8. Replace the wheel cover and its screws.
9. Adjust the tool rest to at least 1/16” (2 mm)
from the accessory and tighten securely.
MAINTENANCE
Your tool has been designed to operate
over a long period of time with a minimum of
maintenance. Continuous satisfactory operation
depends upon proper tool care and regular
cleaning.
Warning! Before performing any
maintenance, switch off and unplug the
tool.
• Regularly clean the ventilation slots in your
tool using a soft brush or dry cloth.
• Regularly clean the motor housing using
a damp cloth. Do not use any abrasive or
solvent-based cleaner.
CLEANING
Blowing dust and grit out of the wheel guards
using compressed air is a necessary regular
maintenance procedure. Dust and grit containing
metal particles often accumulate on interior
surfaces and could create an electrical shock
hazard if not frequently cleaned out.
Always wear
safety glasses.
Caution! Never use solvents or other
harsh chemicals for cleaning the non-
metallic parts of the tool. Use clean, dry
rag only.
ACCESSORIES
The performance of your tool depends on
the accessory used. Black & Decker and
Piranha accessories are engineered to high
quality standards and designed to enhance
the performance of your tool. By using these
accessories you will get the very best from your
tool.
Grinding wheels must fit within the confines of
the guard and must be rated higher than the
recommended speed as marked on the nameplate
(120 V 3450 rpm), (127/220 V 3450 rpm) and
(220V 2950rpm).
Caution! Strands of wire brushes may
break and fly off while in use. Users
and others in the area should wear
adequate eye, face and body protection.
Use only wire brushes that are rated at
or greater than the RPM shown on the
tool’s nameplate. Do not use the spacer
with grinding wheels.
Warning! To reduce the risk of injury,
always use proper guards when grinding
and wear eye protection.