Black & Decker BDCR20, Инструкция по эксплуатации

Страница: 4 / 36

4
WARNING:
Always wear proper
personal hearing protection that
conforms to ANSI S12.6 (S3.19) during
use. Under some conditions and duration
of use, noise from this product may
contribute to hearing loss.
WARNING:
ALWAYS use safety
glasses. Everyday eyeglasses are NOT
safety glasses. Also use face or dust
mask if cutting operation is dusty.
ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA
Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory
protection.
WARNING:
Some dust created by
power sanding, sawing, grinding,
drilling, and other construction
activities contains chemicals known to
the state of California to cause cancer,
birth defects or other reproductive
harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from
chemically-treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust
from power sanding, sawing, grinding,
drilling, and other construction
activities. Wear protective clothing
and wash exposed areas with soap
and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
WARNING:
Use of this tool can
generate and/or disperse dust, which may
cause serious and permanent respiratory
or other injury. Always use NIOSH/OSHA
approved respiratory protection
appropriate for the dust exposure. Direct
particles away from face and body.
WARNING:
Do not operate this
tool for long periods of time. Vibration
caused by the operating action of this tool
may cause permanent injury to fingers,
hands, and arms. Use gloves to provide
extra cushion, take frequent rest periods,
and limit daily time of use.
• When using an extension cord, be sure to
use one heavy enough to carry the current
your product will draw. An undersized cord
will cause a drop in line voltage resulting
in loss of power and overheating. The
following table shows the correct size
to use depending on cord length and
nameplate ampere rating. If in doubt, use
the next heavier gage. The smaller the
gage number, the heavier the cord.
SAvE ThESE INSTRUCTIONS
SYMBOLS
The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:
V ..................volts
A ..................amperes
Hz ................hertz
W .................watts
min ..............minutes
or AC ......alternating current
or DC ...direct current
no ................no load speed
................Class I Construction
(grounded)
................earthing terminal
...............safety alert symbol
................Class II Construction
(double insulated)
.../min or rpm...revolutions or
reciprocation per minute
SPM ............Strokes per minute
............
Read instruction manual before use
................
Use proper eye protection
................
Use proper hearing protection
................
Use proper respiratory protection
IMPORTANT SAFETY
INSTRUCTIONS FOR
BATTERY ChARGERS
SAvE ThESE INSTRUCTIONS: This
manual contains important safety
instructions for battery chargers.
• Before using charger, read all instructions
and cautionary markings on charger,
battery pack, and product using battery
pack.
WARNING:
Shock hazard. Do not
allow any liquid to get inside charger.
CAUTION:
Burn hazard. To reduce
the risk of injury, charge only designated
Black+Decker batteries. Other types
of batteries may burst causing personal
injury and damage.
CAUTION:
Under certain conditions,
with the charger plugged in to the power
supply, the charger can be shorted by
Minimum Gauge for Cord Sets
volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
Ampere Rating
More Not more American Wire Gauge
Than Than
0 - 6 18 16 16 14