Black & Decker BDAS36V, Оригинальное руководство пользователя

Страница: 8 / 76

8
ENGLISH (Original instructions)
u
Plug in the charger (6).
u
Leave the tool connected to the charger for 15
hours.
The charger may hum and become warm while charging; this
is normal and does not indicate a problem.
Warning! Only use the charger provided to charge
BDCS36.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C.
Selecting the direction of rotation (fig. D)
For drilling and for tightening screws, use forward rotation. For
loosening screws or removing a jammed drill bit, use reverse
rotation.
u
To select forward rotation, push the forward/reverse button
(2) to the right.
u
To select reverse rotation, push the forward/reverse button
(2) to the left..
u
To lock the tool, set the forward/reverse button into the
centre position.
Drilling/screwdriving
u
Select forward or reverse rotation using the forward/re-
verse button (2).
u
To switch the tool on, press the on/off switch (1).
u
To switch the tool off, release the on/off switch (1).
LED light
The LED light (4) is activated automatically when the trigger
is depressed. The LED will also illuminate when the trigger is
depressed and the forward/reverse button (2) is in the locked
off position (central position).
Hints for optimum use
Screwdriving
u
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
u
Use the spindle lock to loosen very tight screws or to
firmly tighten screws
u
Always hold the tool and screwdriver bit in a straight line
with the screw.
u
When screwing in wood, it is recommended to drill a pilot
hole with a depth equal to the length of the screw. A pilot
hole guides the screw and prevents splintering or distor-
tion of the wood. For the optimum size of the pilot hole,
refer to the table below.
u
When screwing in hardwood, also drill a clearance hole
with a depth equal to half the length of the screw. For
the optimum size of the clearance hole, refer to the table
below.
Screw size
Pilot hole ø
(softwood) Pilot hole ø
(hardwood) Clearance
hole
No. 6 (3.5 mm) 2.0 mm 2.5 mm 3.6 mm
No. 8 (4 mm) 2.5 mm 3.0 mm 4.5 mm
No. 10 (5 mm) 3.0 mm 3.5 mm 5.0 mm
Drilling pilot holes
u
Always apply a light pressure in a straight line with the drill
bit.
u
Just before the drill tip breaks through the other side of the
workpiece, decrease pressure on the tool.
u
Use a block of wood to back up workpieces that may
splinter.
u
Make an indentation using a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER and Piranha accessories are engineered
to high quality standards and designed to enhance the perfor-
mance of your tool. By using these accessories you will get
the very best from your tool.
This tool uses screwdriver bits with a 1/4" (6.35 mm) hexago-
nal shank. Piranha Super-lok accessories are designed for
use with this tool.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove unplug the charger before cleaning it.
u
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u
Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.