Black & Decker BDAG710, Оригинальное руководство пользователя

Страница: 11 / 16

English
11
(original instructions)
@
Warning! Use extra care when working over an
edge, as a sudden sharp movement of grinder may
be experienced.
Mounting and using cutting (type 41) wheels
Cutting wheels include diamond wheels and abrasive discs.
Abrasive cutting wheels for metal and concrete use are
available. Diamond blades for concrete cutting can also
be used.
NOTE: A closed, 2-sided Type 41 cutting wheel guard is sold
separately and is required when using cutting wheels. Failure
to use proper flange and guard can result in injury resulting
from wheel breakage and wheel contact. Matching diameter
backing flange and threaded clamp nut (included with tool)
must be used for cutting wheels.
Mounting closed (type 41) guard (Fig. J, K)
● Align the three lugs on the guard with the three slots
on the hub. This will align the lugs with slots on the gear
case cover as shown in figure J.
● Push the guard down until the guard lug engages in the
groove on the gear case hub.
● Rotate guard clockwise to lock it into place.
The guard body should be positioned between the spindle
and the operator to provide maximum operator protection.
● Tighten the guard latch screw to secure the guard
on the gear case cover. You should be unable to
rotate the guard by hand. Do not operate grinder with a
loose guard.
● To remove the guard, loosen the guard latch screw.
Then rotate the guard so that the three lugs on the
guard align with the three slots on the hub and pull up on
the guard.
Mounting cutting wheels
● Place the unthreaded backing flange on spindle with
the raised section (pilot) facing up. The raised section
(pilot) on the backing flange will be against the wheel
when the wheel is installed.
● Place the wheel on the backing flange, centering the
wheel on the raised section (pilot).
● Install the threaded clamp nut with the raised section
(pilot) facing away from the wheel.
● Depress the spindle lock button and tighten clamp nut with
included wrench.
● To remove the wheel, depress the spindle lock button and
loosen the threaded clamp nut with included wrench.
@
Warning! Do not use edge grinding/cutting
wheels for surface grinding applications because
these wheels are not designed for side pressures
encountered with surface grinding. Wheel
breakage and injury may result.
● Allow tool to reach full speed before touching tool to
work surface.
● Apply minimum pressure to work surface, allowing
tool to operate at high speed. Cutting rate is greatest
when the tool operates at high speed.
● Once a cut is begun and a notch is established in the
workpiece, do not change the angle of the cut. Changing
the angle will cause the wheel to bend and may cause
wheel breakage.
● Remove the tool from work surface before turning tool
off. Allow the tool to stop rotating before setting it down.
Use
@
Warning! Let the tool work at its own pace. Do
not overload.
● Carefully guide the cable in order to avoid accidentally
cutting it.
● Be prepared for a stream of sparks when the grinding or
cutting disc touches the workpiece.
● Always position the tool in such a way that the guard
provides optimum protection from the grinding or
cutting disc.
Switching on and off
● To switch the tool on, press the on/off switch (1).
● To switch the tool off, release the on/off switch (1).
@
Warning! Do not switch the tool off while under load.
Hints for optimum use
● Firmly hold the tool with one hand around the side
handle and the other hand around the main handle.
● When grinding, always maintain an angle of approx.
15° between the disc and the workpiece surface.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
@
Warning! Before performing any maintenance on
corded/cordless power tools:
● Switch off and unplug the appliance/tool.
● Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
● Or run the battery down completely if it is integral and then
switch off.
● Unplug the charger before cleaning it. Your
charger does not require any maintenance apart from
regular cleaning.
● Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
● Regularly clean the motor housing using a damp
cloth. Do not use any abrasive or solvent-based cleaner.
● Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
● Safely dispose of the old plug.
● Connect the brown lead to the live terminal in the
new plug.
● Connect the blue lead to the neutral terminal.