8
1.
DO NOT OPERATE THIS MACHINE
until it is completely assembled and installed according to the instructions. A machine incorrectly
assembled can cause serious injury.
2.
OBTAIN ADVICE
from your supervisor, instructor, or another qualified person if you are not thoroughly familiar with the operation of this
machine. Knowledge is safety.
3.
FOLLOW ALL WIRING CODES
and recommended electrical connections to prevent shock or electrocution.
4.
SECURE THE MACHINE TO A SUPPORTING SURFACE.
Vibration can possibly cause the machine to slide, walk, or tip over, causing
serious injury.
5
.
USE ONLY CROSSCUT SAW BLADES.
Use only zero-degree or negative hook angles when using carbide-tipped blades. Do not use
blades with deep gullets. These can deflect and contact the guard, and can cause damage to the machine and/or
serious injury.
6.
USE ONLY BLADES OF THE CORRECT SIZE
AND TYPE
specified for this tool to prevent damage to the machine and/or serious injury.
7.
USE A SHARP BLADE.
Check the blade to see if it runs true and is free from vibration. A dull blade or a vibrating blade can cause
damage to the machine and/or serious injury.
8.
INSPECT BLADE FOR CRACKS
or other damage prior to operation. A cracked or damaged blade can come apart and pieces can be
thrown at high
speeds, causing serious injury. Replace cracked or damaged blades immediately.
9.
CLEAN THE BLADE AND BLADE FLANGES
prior to operation. Cleaning the blade and flanges allows you to check for any damage to
the blade or flanges. A cracked or damaged blade or flange can come apart and pieces can be thrown at high speeds, causing serious
injury.
10.
USE ONLY BLADE FLANGES
specified for this tool to prevent damage to the machine and/or serious injury.
11.
CLEAR THE AREA OF FLAMMABLE LIQUIDS
and/or gas prior to operation. Sparks can occur that would ignite the liquids and cause
a fire or an explosion.
12.
CLEAN THE MOTOR AIR SLOTS
of chips and sawdust. Clogged motor air slots can cause the machine to overheat, damaging the
machine and possibly causing a short which could cause serious injury.
13.
TIGHTEN THE TABLE CLAMP HANDLE
and any other clamps prior to operation. Loose clamps can cause parts or the workpiece to
be thrown at high speeds.
ADDITIONAL SPECIFIC SAFETY RULES
WARNING:
READ ALL INSTRUCTIONS BEFORE OPERATING PRODUCT. FAILURE TO FOLLOW ALL INSTRUCTIONS
LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND OR SERIOUS INJURY.
Содержание 90528012
