Upper Cord Wrap Hook Assembly - PW1600
Insert cord wrap top hook
(M)
into the rear
slot in handle
(K),
pushing down firmly until it
stops. Drive two
1 1/2”
self tapping screws
included in cord hook bag through handle
holes into cord wrap hook as shown until
tight.
DO NOT
over tighten.
PW1750 ASSEMBLY:
Tools Required:
Philips screwdriver
Adjustable wrench
Hardware Bag Contents:
- 2 pcs. flat washers
- 2 pcs. hex locking nuts
Wheel Assembly - PW1750
Remove the 2 protective plastic end caps
from axle and discard. Place wheel
(E)
with 5
raised square bumps facing outwards as
shown below over threaded axle end,
followed by flat washer, and hex locking nut.
Using wrench, tighten nut securely. Align 5
square knotches in wheel cap
(E1)
to raised
PW1600
1
3
4
2
“UP”
Label
UNIT ASSEMBLY
PW1600 ASSEMBLY:
Tools Required:
Philips screwdriver
Adjustable wrench
Hardware Bag Contents:
- 2 pcs. flat washers
- 2 pcs. hex locking nuts
- 6 pcs.
5/8”
screws
Wheel Assembly - PW1600
Remove the 2 protective plastic end caps
from axle and discard. Place wheel
(E)
, flat
washer, and hex locking nut over axle end
as shown with smooth face of wheel having
circular holes only facing outwards (side of
wheel with raised spokes faces inwards
toward pressure washer body). Using a
wrench, tighten nut securely. Align wheel
cap
(E1)
over wheel face as shown and
press center of wheel cap until it snaps
securely to wheel.
Handle Assembly - PW1600
1.)
With rectangular steel tube
(N)
ends
pointing upwards as labeled, push tubes
down firmly into rectangular holes in black
top housing
(P)
until they hit bottom.
2.)
Drive one
5/8”
screw through the hole in
each side of the orange housing
(Q)
as
shown and into the tapped hole of the tube
until tight.
3.)
Next drive one
5/8”
screw through each
hole in the upper back side of the black top
housing
(P)
as shown into the tapped hole
of the tube until tight.
4.)
You are now ready to align the
rectangular holes in bottom of handle
(K)
over the tubes, pushing the handle down
until it’s bottom edge slides into black
housing
(P)
fully. Drive one
5/8”
screw
through each hole in the back of the handle
(K)
as shown into the tubes until tight to
complete handle assembly.
4
A.
High pressure water outlet (OUTLET)
B.
Pump Quick Connector
C.
High pressure turbo wand
D.
Adjustable fan wand
E.
Wheels
E1.
Wheel Cap
F.
Gun
F1.
High pressure hose connector
F2.
Gun safety catch
G.
Power supply cord with GFCI
H.
Hardware bag
I.
On/off switch
J.
Garden hose Quick Connector
K.
Handle
L.
Removable detergent tank with cap
M.
Cord wrap top hook
N.
Steel Support tubes
O.
Nozzle Cleaning tool
P.
Black top housing
Q.
Orange main housing
F
F1
F2
H
O
I
I
K
L
J
M
N
O
B
E1
E
D
P
Q
C
O
I
E1
F
F1
F2
I
K
L
J
H
M
O
D
C
E
G
N
Q
A
P
B
PW1600
PW1750
5
2
1
PW1600
3
PW1600
