BKT Elektronik ACBS Скачать руководство пользователя страница 45

Страница: 45 / 92

www.bkte.pl

BKT ACBS - installation and configuration manual of the access control system with RS485 bus interface

7.2

Card reader low level configuration

Connecting the reader

For low-level configuration, the reader should be connected to the computer via the RUD-1 interface. If the reader is already installed on
the cabinet door, then:

Disconnect the reader's AW111 cable from the controller by unplugging the RJ45 connector.

Connect the RJ45 plug of the AW111 cable to the RUD-1 interface as shown in the figure below.

Putting the reader into the service mode

AR121 and AR122 readers (UNIQUE readers) do not require any
additional steps.
In AR131 and AR132 readers (Mifare readers) you should:

Remove the MEM jumper on the reader

Restart the reader (turn off and turn on the power or short
RST jumper for a moment) - orange LED SYSTEM reader will
start to flash

The reader is ready for low-level configuration

After completing the configuration, put the MEM jumper back,
which will enable later remote configuration of the reader from
the VISO program.

Содержание ACBS





























































































Результаты поиска

Содержание ACBS

Отзывы:

Похожие инструкции для ACBS

Бренды по названию

Популярные бренды

BKT Elektronik ACBS, Руководство по установке и настройке

Результаты поиска

Содержание ACBS

Отзывы:

Похожие инструкции для ACBS

Бренды по названию

Популярные бренды