BKI Ventless Hood System FH-28 Скачать руководство пользователя страница 21

Страница: 21 / 24

Ventless Hood System

Installation

Appliance Electrical Connection

This connection is for appliances requiring a UL listed flexible conduit connections (refer to figure below).

1. Remove receptacle and four wires (T1, T2, T3, and Ground).

2. Cover junction box hole with provided plate and hardware removed from receptacle.

3. Remove hole plug from hole in bottom of electrical enclosure and install conduit from appliance

utilizing appropriate UL Listed fitting (not provided).

4. Wire appliance as shown in figure below and the electrical diagram in this manual.

5. Replace all panels and install cover over hole that was provided for the receptacle (now removed)

Содержание Ventless Hood System FH-28

























Результаты поиска

Содержание Ventless Hood System FH-28

Отзывы:

Похожие инструкции для Ventless Hood System FH-28

Бренды по названию

Популярные бренды

BKI Ventless Hood System FH-28, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Ventless Hood System FH-28

Отзывы:

Похожие инструкции для Ventless Hood System FH-28

Бренды по названию

Популярные бренды