BKI BLF-F Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 56

background image

Automatic Lift Fryer

Introduction

3

Specific Precautions

Risk of fire exists if the oil level drops below 5mm of the maximum oil level.

Use of oil/shortening older than the manufacturers recommendations for life of
the oil is prone to surge boiling and flash fires. Follow the oil manufacturers
guidelines for the life cycle of oil/shortening.

Do not open the drain valve or the fill valve while the fryer is under pressure.
Serious burns may result.

Follow operator instructions regarding effects of surge boiling of over-wet foods
and proper load size.

This unit may incorporate components that contain Mercury. The use of Mercury
relays is an industry standard.

Equipotential ground plane

When a high current flows through a conductor, differences in potential appear
between the conductor and nearby metallic surfaces near the appliance. As a
result, sparks may be produced between the appliance and surrounding metal
surfaces. These sparks could cause serious injury, damage, or fire.

BKI provides an Equipotential ground terminal for the connection of a bonding
conductor after the installation of the appliance per lEC60417-1. This terminal is
located on the inside of the Power Entry Supply box near the Earth connection
and is marked with this symbol.

Full Disconnection

In accordance with Local and/or National wiring codes, the installer must provide
a means of full disconnection under over voltage Category III conditions. An IEC
approved cord and plug combination will meet this requirement.

Units not provided with a cord and plug do not meet this requirement. In
accordance with Local and/or National wiring codes, the installer must provide
the means of full disconnection.

The fryer is designed to hold a maximum of 75 lb (34 kg) of oil/shortening.

«
...
3
4
5
6
7
...
»

Содержание BLF-F

























































Отзывы:

Нет отзывов

Похожие инструкции для BLF-F

Бренд: T-Fal Страницы: 51

Бренд: Emerald Страницы: 32

Бренд: GE Страницы: 20

PRIMOTECQ TW730E

Бренд: FUST Страницы: 60

Бренд: Presto Страницы: 6

Harry Ramsden’s 45362

Бренд: Morphy Richards Страницы: 8

Бренд: Zenith Страницы: 20

Бренд: Smeg Страницы: 16

Бренд: Hendi Страницы: 64

Бренд: Haier Страницы: 16

HDY-C70 WH HA AA

Бренд: Haier Страницы: 17

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 17

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 32

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды