Bizerba GSP H Скачать руководство пользователя страница 3

Страница: 3 / 92

Instruction manual GSP

Table of Contents

3 / 92

38107010002 en-US

Table of Contents

About these instructions ....................................................................................

1.1

Safe-keeping ........................................................................................

1.2

Target group .........................................................................................

1.3

Symbols used .......................................................................................

1.4

Warnings ..............................................................................................

About this machine .............................................................................................

2.1

Intended use.........................................................................................

2.2

Machine description..............................................................................

2.2.1

Components of the manual slicer .........................................................

2.2.2

Components of the automatic slicer .....................................................

2.2.3

Accessories ..........................................................................................

2.3

Directives..............................................................................................

2.4

Warranty ...............................................................................................

2.5

Disposal of the machine / environmental protection.............................

Safety instructions ..............................................................................................

3.1

General notes on safety .......................................................................

3.2

Safety instructions for transport and installation...................................

3.3

Safety instructions during operation, slicing .........................................

3.4

Safety instructions for sharpening, cleaning.........................................

3.5

Protective and safety devices...............................................................

3.6

Plates on machine ................................................................................

Installation............................................................................................................

4.1

Transport and storage ..........................................................................

4.2

Installation and assembly .....................................................................

4.2.1

Installation requirements ......................................................................

4.2.2

Electrical connection.............................................................................

4.2.3

Leveling ................................................................................................

4.2.4

Attaching product feed for tomatoes.....................................................

4.2.5

Attaching vegetable hopper..................................................................

4.3

Start-up.................................................................................................

4.3.1

Switching the slicer on..........................................................................

4.3.2

Switching the machine off.....................................................................

4.4

Decommissioning .................................................................................

Machine and operating elements.......................................................................

5.1

Membrane keyboard GSP H ................................................................

5.1.1

HMI touchscreen GSP H W..................................................................

5.2

Membrane keyboard GSP HD..............................................................

5.2.1

HMI touchscreen GSP HD....................................................................

5.2.2

Membrane keyboard GSP HD W with HMI touchscreen......................

5.3

Slice thickness adjustment ...................................................................

Содержание GSP H





























































































Результаты поиска

Содержание GSP H

Отзывы:

Похожие инструкции для GSP H

Бренды по названию

Популярные бренды

Bizerba GSP H, Инструкция по эксплуатации

Результаты поиска

Содержание GSP H

Отзывы:

Похожие инструкции для GSP H

Бренды по названию

Популярные бренды