BIXOLON SRP-330II Скачать руководство пользователя

Страница: 21 / 125

SRP-330II/332II

Rev. 1.00

BIXOLON

- 21 -

ESC *

Function:

Specify bit image mode

Code:

ASCII

ESC

d1...dk

Hex

d1...dk

Decimal

d1...dk

Range:

m = 0, 1, 32, 33
0 ≤ nL ≤ 255
0 ≤ nH ≤ 3
0 ≤ d ≤ 255
k = nL + nH × 256 [in case of m = 0, 1]
k = (nL + nH × 256) × 3 [in case of m = 32, 33]

Default:

None

Description:

■

This command specifies the bit image for the mode m as to the number of dots specified by nL and nH.

•

d specifies the bit image data with 1 for printed data and 0 for not printed.

•

k denotes the number of horizontal dots.

Remarks:

■

If the bit image data being entered is beyond the number of dots to be printed, the surplus will be discarded.

■

If the value of m is beyond the conditions, the subsequent data after m will be treated as normal data.

Differences:

■

SRP-330II :

DPI : Dots per Inch (25.4mm)

Mode

Number o dots in

vertical direction

Vertical dot

density (DPI)

Horizontal dot

density (DPI)

Number of bytes (k)

8-dot single-density

nL + nH x 256

8-dot double-density

180

nL + nH x 256

24-dot single-density

180

(nL + nH x 256) x 3

24-dot double-density

180

(nL + nH x 256) x 3

Содержание SRP-330II






























































































































Результаты поиска

Содержание SRP-330II

Отзывы:

Похожие инструкции для SRP-330II

Бренды по названию

Популярные бренды

BIXOLON SRP-330II, Руководство по управлению

Результаты поиска

Содержание SRP-330II

Отзывы:

Похожие инструкции для SRP-330II

Бренды по названию

Популярные бренды