Normal cleaning
1.
Plug the OXYPowerBrush into a proper
outlet and turn the power switch ON.
2.
While pressing the spray trigger, make one
slow forward and backward wet pass. Let
the BISSELL advanced deep cleaning
formula and DirtLifter PowerBrush do the
work for you. Caution: Do not overwet.
3.
Release the spray trigger and make one
slow forward and back pass over the same
area to remove any residual dirty water.
4.
Repeat cleaning passes without press-
ing the spray trigger until you can’t see any
more water being suctioned up.
5.
When cleaning job is complete, refer to
the Maintenance and care section on
page 9 for machine cleanup and
storage instructions.
To use the OXY PowerTool
1.
Pull out the rubber stopper in the tank
and lay tool on its side.
2.
Fill tool with OXYgen Boost formula and
replace the rubber stopper.
3.
Attach tool to machine hose and clean
according to machine instructions.
C5 - Cleaning bare floors
The bare floor tool provides effective
cleaning for linoleum, vinyl, and tile floors.
Caution: Do not use on hardwood floors
1.
Use only BISSELL Hard Floor Solutions.
2.
Vacuum or sweep thoroughly to pick up
loose debris and pet hair
3.
Remove easily moved furniture from the
room (chairs, tables, etc.)
4.
Plan your cleaning route to leave an
exit path.
5.
Plan activities to allow 30 minutes for
the floor to dry completely.
C6 - Attach the bare floor tool
1.
Step on the handle release to lay the
machine handle down.
2.
Remove the Tank-in-Tank from the
machine base.
3.
Lift the machine base to expose the
underside of the nozzle.
4.
Attach bare floor tool to nozzle with long
tab to the right side (ReadyTools side) of the
nozzle.
5.
First attach left side (short tab) catching
tab over nozzle edge.
6.
Gently bend long tab (right side) outward
to easily snap over edge of clear nozzle
on left.
Machine preparation
1.
Set up machine following instructions on
pages 6. Be sure to thoroughly rinse out
any remaining BISSELL advanced deep
cleaning formula from the Tank-in-Tank to
prevent slippery linoleum, vinyl, and tile
floors. Use BISSELL Hard Floor Solution in
the Tank-in-Tank.
2.
Check ReadyTools dial - it should be set
on FLOOR CLEANING.
3.
Plug into a proper outlet and turn power
switch ON.
Bare floor cleaning technique
1.
Slowly move the machine nozzle with
bare floor tool forward and back over
soiled surface one time while pressing the
spray trigger.
Caution: Do not over wet.
2.
Repeat the motion without pressing the
spray trigger, using the bare floor tool to
squeegee and suction up the dirty water.
3.
Repeat steps 1 and 2 backing along the
exit path.
4.
Allow about 30 minutes for the floor to
dry completely.
5.
When the cleaning job is complete refer to
the Maintenance and care section on page 9
for machine cleanup and storage instructions
6.
To remove bare floor tool gently bend
long tab (right side) outward and pull tool
down away from nozzle. Rinse thoroughly,
dry and store.
C7 - Cleaning upholstery
and small areas
Important–Check upholstery tags.
1.
Check manufacturer’s tag before cleaning.
A “W” or “WS” on the tag means you can
use your OXYPowerBrush. If the tag is coded
with an “X” or “S” (with a diagonal strike
through), or says “Dry Clean Only,” do not
proceed. Do not use your OXYPowerBrush
on velvet, silk, 100% cotton upholstery, vinyl
or leather. If manufacturer’s tag is missing or
not coded, check with your furniture dealer.
2.
Check for colourfastness in an
inconspicuous place.
3.
If possible, check upholstery stuffing.
Coloured stuffing may bleed through fabric
when wet.
4.
Plan activities to give upholstery time
to dry.
5.
Vacuum thoroughly to pick up loose
debris and pet hair. Use a vacuum with a
brush attachment and a crevice tool to
clean in fabric folds and tufts.
www.BISSELL.com
8
Содержание OXY POWERBRUSH 16949 SERIES
Страница 1: ...OXY POWERBRUSH USER GUIDE 16949 SERIES...
