Special features
Built-in-Heater switch (red)
The Little Green® PROHeat model gives you
the ability to raise the water temperature for
improved cleaning performance based on your
cleaning needs.
Heat indicator light
After turning the built-In heater switch on, the
heat indicator light will illuminate,
indicating the heater has reached the
correct temperature.
Flex hose clip
The clip guides the storage of the vacuum flex
hose around the unit.
TurboBrush clip
Attaches to the unit for storage of the 2-in-1
crevice tool or TurboBrush.
Tough stain brush
The standard tool that attaches to the
flex hose.
Quick Release cord wrap
To remove the power cord, gently twist/rotate
the Quick Release cord wrap clockwise.
Power Cord
The power cord, with a three-prong plug, stores
on the back of the Little Green by wrapping
around the Quick Release cord wrap.
NOTE: Unwrap the Power Cord completely
before operating the unit.
Getting ready
1.
To fill the clean water/solution tank.
a.
Remove the tank by lifting it straight up
and then away from the unit.
b.
Unscrew the black cap at the bottom of
the clean/solution tank.
c.
Add BISSELL 2X Portable Formula to
the FORMULA fill line on the clean/solution
tank. Fill the clean/solution tank with hot
(NOT boiling) tap water to the WATER fill
line.Replace and tighten the black cap.
DO NOT BOIL OR MICROWAVE WATER.
d.
Replace the clean/solution tank by
lining up the vertical guides on the left
side of the unit with the indentations on
the clean/solution tank and gently sliding
it down into position.
2.
Unwrap vacuum flex hose completely from
onboard hose storage.
3.
Attach your selected cleaning tool to the
spray trigger unit by pressing tool onto spray
trigger firmly until the button lock snaps into
hole. Make certain the tool is securely attached.
4.
Twist the quick release cord wrap clockwise
to unwrap the power cord completely from
onboard cord storage and plug into 120 Volt, 60
Hz grounded outlet as described in Important
Safety Instructions”, page 2.
5.
Press power switch to ON position. Press the
red heater switch to “ON”. Within 30 seconds,
the heat indicator light will illuminate, indicating
the heater has reached the proper temperature.
6.
Begin by pressing the spray trigger for 5-10
seconds to allow the non-heated water to travel
through the heater.
7.
Press and hold spray trigger—spray will start
in a few seconds. Raise the tool slightly to check
for spray.
Pre-treating
Cleaning effectiveness will be enhanced if you
pre-treat heavily stained or highly-soiled areas.
Here’s how to do it:
1.
Hold the cleaning tool just above the surface
of the carpet or upholstery to be cleaned. Press
the trigger to release a spray of cleaning solution
directly onto the soiled area.
2.
Wait 3-5 minutes before cleaning.
Cleaning with your Little Green PROheat
1.
Hold the tool approximately 1” above the
soiled surface. Press the spray trigger to apply
the cleaning solution to the soiled area.
2.
Using the brush on the tool, gently scrub
the area to be cleaned.
NOTE: When using the Deep Reach Tool
(select models), keep the tool in contact
with the carpet while spraying. If using the
TurboBrush® Tool, the switch should be
in the “BRUSH” position. This activates the
brush only.
3.
For thorough cleaning, spray additional
solution while the brush and suction are in
contact with the surface.
Operations
www.BISSELL.com
800.237.7691
www.BISSELL.com
800.237.7691
WARNING
Keep spray away from face. Failure to do
so may result in personal injury.
IMPORTANT
Check the manufacturer’s tag before
cleaning upholstery. “W” or “WS” on the
tag means you can use your Little Green
ProHeat. If tag is coded with an “S” (with
diagonal strike-through), or says “Dry Clean
Only,” do not proceed. If manufacturer’s tag
is missing or not coded, check with your
furniture dealer.
7
6
Operations
1a.
1c.
1b.
1d.
3.
2.
5.
4.
6.
Power
Switch
Heater
Switch
Spray
Trigger
» Deep cleaning stairs and high-traffic areas on
a regular basis helps prolong carpet life.
» Check upholstery stuffing before cleaning.
Colored stuffing may bleed through the fabric
when it becomes wet.
» If a significant amount of water and solution
remains in the clean tank, your unit can be stored
with liquid in the clean tank.
Tips
WARNING
Be sure to unplug the cord before attaching the TurboBrush
(select models only).
2.
