Bison Magic VB4000, Первоначальные инструкции по установке

Страница: 7 / 14

7
42. Once you are satisfied that the VB1250K Net (N) is set up correctly with proper tension and at the
Women's height, retighten the set screw that holds the top rope guide in place. Once set up correctly at
Women's height the first time, future set up for Men's (M), Women's (W) and Junior (J) height will
require no additional adjustment of the top rope guide and should be 100% repeatable. See Photo 29.
43. It is acceptable to remove excess top and bottom rope material from the winch post ends if desired. The
ropes are provided extra long to allow installation of the VB1250K Net (N) on posts that are further apart
than our recommended 37' center to center (see attached court layout diagram). It is advisable to leave 2'-
3' extra rope to allow future adjustments and easy tensioning of the bottom rope. When court is in use,
the extra rope will be hidden behind the safety padding.
44. Prior to play, attach the
VB51P Pole Padding (S) after placing the winch tensioning handle in the storage
position. See Photos 33 and 42.
45. Install white top and bottom
Cable Covers (Q). These may need to be shortened with a scissors by
trimming just outside the sewn seam depending on how far apart the posts are installed.
46. Install
VB13 Boundary Markers and Antennas (R) on the court boundary lines. Note that the antenna is
two piece and that the top section can be stored in the boundary marker pocket leaving the assembly
attached to the net while not in use.
47. Install the optional
Official's Platform (V) following the instructions supplied with the platform.
48. Your initial installation is now complete. Future installation should be simple, quick and repeatable.
See Photo 44.
49. To store the Magic System, remove
Officials Platform (V) (if applicable), VB51P Pole Padding (S),
VB1250K Net (N) and other components attached to the pole. All items except the Officials Platform (V)
and the VB51P Pole Padding (S) can be stored in the Zippered Carrying Bag (T) supplied with each
system. See Photo 43.
50. To lower the
Telescoping Pole (A) into the floor, lower each section starting at the top being careful to
keep clothing, jewelry and body parts away from moving parts. Start with the top section and lower each
one slowly to reduce the chance of damage. Using the supplied
Screwdriver (Z) press in on the spring pin
while holding the pole, then lower each pole carefully. Continue that process down to the largest
diameter section, lift up on that section then rotate approximately 10° counter clockwise then carefully
lower the post into the socket. See Figure 2.
51. Make sure that the
Telescoping Pole (A) is fully retracted prior to closing the VB23-CV Brass Floor
Plate (E).
52. The pole assembly is held in place by a
Key Block (BB). Inside the Key Block (BB) is a Set Screw (DD)
and a 3/8 Nylon Ball (AA). With continued use the 3/8 Nylon Ball (AA) may get damaged. We have
included 6 extra 3/8 Nylon Balls (AA). If pole #1 of the pole assembly becomes hard to raise and lower
or you notice visible damage to the 3/8 Nylon Ball (AA) simply remove the two 1/4” Bolts (CC) and
remove the Key Block (BB). Tighten the Set Screw (DD) until the damaged 3/8 Nylon Ball (AA) falls
out. Loosen the Set Screw (DD) and then replace the 3/8 Nylon Ball (AA) with one of the 6 that are
included in the hardware. Reinstall the Key Block (BB) then tighten the Set Screw (DD) until the 3/8
Nylon Ball (AA) contacts pole #1, then loosen 1/4 to 1/2 turn. Contact your dealer if you need more
replacement 3/8 Nylon Balls (AA). See Figure 3.