Bishamon SPA4000 Скачать руководство пользователя страница 26

Страница: 26 / 32

11-8. Hydraulic Pipes

<Hydraulic pipe bundling>

1. Check that the hydraulic pipes are securely

bundled to the post.

2. In particular, repair if the bands as shown in the

diagram on the right are broken or loose.

11-9. Hydraulic Oil

<Replacing hydraulic Oil>

1. Replace the hydraulic oil 1 year after start of use. Replace completely every 3 years from the 2

time

onwards.

①

Remove the hydraulic unit cover.

②

Remove the drain plug at the bottom of the oil tank (see

arrow in the diagram on the right), and drain the hydraulic

fluid. Securely tighten the drain plug after drainage.

③

Remove the oil tank lid, and check the suction filter

condition. Clean or replace if there is any dirt or rust.

④

Add hydraulic oil from the top of the oil tank to the

regulation amount (8.5L).

⑤

Raise the lift and check that there are no abnormalities.

Further, the device uses gear pumps and performance is greatly affected by the hydraulic fluid used, so

make sure to select from among the following reputable brands.

Viscosity: ISO VG32 wear-resistant hydraulic fluid (use amount: 8.5L)

Idemitsu

Super Hydraulic Fluid 32

JX Nippon Oil & Energy

Super Hydrand 32

Esso

Nuto H32, Unipower SQ32, XL32

Mobil

Mobil DTE Oil 24

Showa Shell Sekiyu

Terasu Oil 32, K32

Replacement method

1. Be very careful not to touch the high-voltage parts during inspections.

2. After removing the cover and implementing inspections, make sure to use all the mounting

screws to restore the original condition.

3. If, as a result of the inspection, an abnormality is detected, stop using the lift immediately

and contact your supplier for repairs.

Caution

Hydraulic unit cover

Oil tank

Drain plug

M post

S post

Содержание SPA4000

































Результаты поиска

Содержание SPA4000

Отзывы:

Бренды по названию

Популярные бренды

Bishamon SPA4000, Руководство пользователя

Результаты поиска

Содержание SPA4000

Отзывы:

Бренды по названию

Популярные бренды