manualshive.com logo in svg

BIS TRADITION, Инструкция по установке и эксплуатации, Страница: 41 / 44

Поделиться
Скачать
BIS TRADITION Скачать руководство пользователя страница 41

36

4.7

INSTALLATION INSTRUCTIONS FOR MASONRY APPLICATION

WARNING

:

Before starting the installation, the masonry chimney  must  be inspected  by
a qualified sweep.

The following requirements must be respected:
1.

 

The chimney must  be absolutely  clear of  any soot  residue or  creosote.    Check  for  cracks,  loose  or  missing

bricks that could inhibit correct installation of the liner.

2.

 

The clearance to  combustible  must  be a minimum  of  1"  between the  outside  of  the  masonry  and  any  wood

framing or loose insulation.

3.

 

The chimney must be built in accordance with the current building code.

4.

 

No other appliance can be connected to the same chimney.

5.

 

The clearances to combustible  for the  BISTMA30  or  BISTMA  connectors are 2"  on  the  side  and bottom  and

16" at the top.

6.

 

The connector parts  are not  necessary if  the  connection  between the  insulated  length  and  the  stainless

steel liner is done within the masonry chimney

.

Installation:

The chimney must be relined with a stainless steel liner model Tubinox or Projet SS of the same  diameter as

the outlet of the fireplace.
For connection at 45º angle, a special connector (BISTMA for the BIS  TRADITION  fireplace) must  be  used

to connect the liner to the insulated chimney.  For connection at 30º, use the BISTMA30 connectors.

Follow these steps:
1-

 

Position  the  fireplace  in  its  location.

Temporarily install  the  S2100+  elbow  on

the  top  of  the  fireplace and,  using  a  level,

mark with  an  oval  the  location  where  the

flue liner will enter the masonry chimney.

2-

 

In the middle of the oval, drill a hole in the

masonry chimney at 45º or 30º.

3-

 

Increase the  size of  the  hole  until  a 45º  or

30º  Tubinox  liner  elbow  can  be  easily

slipped through.

4-

 

Slide  the  liner  down  from  the  top  of  the

masonry chimney until  you  reach the  hole

level.

5-

 

Slip  through  the  hole  a  45º  or  30º  liner

elbow and connect it to the liner.

6-

 

Add a small liner section to the liner  elbow

which will allow the liner to extend at  least

12” (measured at the  top  of  the  liner) from

the masonry chimney.   

7-

 

Seal the opening around the liner with  high

temperature refractory cement.

8-

 

The next steps must be done in the

following order :
A.

 

Select the S2100+ length that will fit between the elbow and the liner  so  that  it  will  slide  at  least  2

"

 over

the liner section. (You may need to cut the liner for a better fit).

B.

 

Take that section and the BISTMA OR BISTMA30 cover and slide it over  the  liner.    Make sure you  have

enough opening to be able to install the S2100+ elbow without difficulty.

C.

 

Install the 45º or 30º elbow on the fireplace.

D.

 

Slide the length section back down on the elbow and twist lock the two together.

E.

 

Pull  the  cover down  over the  length  and install  the  insulation  pad over the  liner;  be careful to  cover the

liner completely.

F.

 

Slide back the cover over the insulation and fix it in place using the 3 metal screws supplied.

See typical installation illustrated below

Содержание TRADITION













































Отзывы:

Нет отзывов