BIRO MINI-22 Скачать руководство пользователя страница 18

Страница: 18 / 28

CLEANING

BEFORE CLEANING OR SERVICING

ONLY Use Recommended Cleaning Equipment, Materials, and Procedures.
NEVER Spray Water or Other Liquid Substances Directly at Motor, Power Switch or any Other

Electrical Components.

ALWAYS Thoroughly Clean Equipment at Least Daily.

ALWAYS Turn Off and Unplug Machine from Power Source and Perform Lockout/Tagout Procedure to This

Machine Before Cleaning or Servicing.

CLEANING THE MINI-22 MIXER GRINDER

1. Disconnect mixer grinder from power source and perform lockout/tagout procedures.

2. Remove end ring, breaker plate, knife and grinding auger.
3. Remove mixing paddle, bowl and hopper from the machine (see page 15 for procedures).

4. Machine is now ready to be cleaned using warm soapy water and rinsed with clean water. Machine may be

cleaned by power spray washing, taking care not to spray directly at any electrical controls.

5. After machine has been cleaned and allowed to air dry, all exposed metal surfaces should be coated with a

good food grade light oil or grease.

REMOVAL/INSTALLATION INSTRUCTIONS

PADDLE REMOVAL:

Open hopper cover, loosen the paddle lock thumb screw(thumb screw located at front of hopper). While

holding mixing paddle, turn lock arm clockwise, and remove lock arm from hopper. Next remove paddle

drive end from square drive. Then remove paddle from hopper.

PADDLE INSTALLATION:

Install paddle drive end into square drive. Holding mixing paddle, align paddle shaft to the lock arm. Slide

lock arm into hopper onto the shaft. Turn counterclockwise to lock position. Tighten thumb screw.

BOWL/HOPPER REMOVAL:

Remove ring, breaker plate and knife. Auger can now be pulled out from grinding bowl. Using 19mm

wrench, loosen and remove both hex nuts from bowl flange. Remove bowl by pulling away from hopper

studs. Remove hopper from frame by pulling from front of machine.

BOWL/HOPPER INSTALLATION:

Install hopper onto frame, slide back into position. Install bowl onto the hopper studs, install and tighten hex

nuts to secure bowl. Slide the auger into bowl, install knife, breaker plate and ring.

Note: Ring is to be hand tightened only.

Содержание MINI-22





























Результаты поиска

Содержание MINI-22

Отзывы:

Бренды по названию

Популярные бренды

BIRO MINI-22, Руководство по эксплуатации и список запасных частей

Результаты поиска

Содержание MINI-22

Отзывы:

Бренды по названию

Популярные бренды