BIRD Termaline 8890-300SC13 Скачать руководство пользователя страница 22

Страница: 22 / 25

Termaline® Semiconductor Load Resistor

Shipping the Semiconductor

Remove the vent plug.

Replace it with the shipping plug.

Wrap the vent plug with padding.

tape it to the side of the load for protection.

Note:

With the shipping plug installed, it is not necessary to empty out the coolant.

Wrap the connector in padding.

Pack and brace the load in a sturdy wooden crate for shipment.

Customer Service

Any maintenance or service procedure beyond the scope of those in this chapter should be referred to a qualified
service center.

If the unit needs to be returned for any reason, request an Return Material Authorization (RMA) through the Bird
Technologies website. All instruments returned must be shipped prepaid and to the attention of the RMA number.

Bird Service Center

30303 Aurora Road
Cleveland (Solon), Ohio 44139-2794
Fax: (440) 248-5426
E-mail:

[email protected]

For the location of the Sales Office nearest you, visit our Web site at:

http://www.birdrf.com

Содержание Termaline 8890-300SC13


























Результаты поиска

Содержание Termaline 8890-300SC13

Отзывы:

Похожие инструкции для Termaline 8890-300SC13

Бренды по названию

Популярные бренды

BIRD Termaline 8890-300SC13, Руководство по эксплуатации

Результаты поиска

Содержание Termaline 8890-300SC13

Отзывы:

Похожие инструкции для Termaline 8890-300SC13

Бренды по названию

Популярные бренды