background image

1

Chapter 1

Introduction

Purpose and Function

The Model 8792 Termaline Load Resistors are designed as compact, low-reflection, and non-radiating termination 
for RF transmission lines. Cooled by internal water flow, it generates almost no surface heat, making installation 
space minimal and convenient. They can safely dissipate up to 80 kilowatts of continuous power when used in a 50 
ohm coaxial transmission line system.

Each model is designed for use with a standard connector of the types common to 6-1/8 inch coaxial lines, and will 
maintain a VSWR of less than 1.15 to 1.0 from 1000 Hz up to 800 MHz. These loads are intended for use on CW, AM, 
FM, SSB, and W modulation envelopes, and within certain limitation on radar or pulse modes. Information on 
applications involving pulse-type signals should be obtained directly from Bird Electronic Corporation.

Description

The Model 8792 equipment consists of a load resistor unit. They have field replaceable resistive element.  The 
replacement procedure is included in 

"Maintenance" on page 8

.

Optional Equipment

An accessory protective Control System is available as optional equipment. When properly installed, this system 
protects the load by shutting off the RF power when water flow is too low or interrupted. Discussions of the flow 
control pertaining to 

"Installation" on page 4

 and 

"Maintenance" on page 8

 should be ignored when not 

applicable. 

Direct Power Measurement 

When used in conjunction with a Bird Model 6810 Series Thruline Wattmeter or 3127 Series Panel Meters, these 
load resistors may be used for direct reading power measurements up to 80 kilowatts.

Emergency and First Aid Procedures for Ethylene Glycol

Eye 

Contact — 

Immediately flush eyes with plenty of water for at least 15 minutes while holding eyelids open. 

Get medical attention.

Skin Contact — 

Flush skin with water. If irritation occurs, get medical attention.

Inhalation — 

Remove victim to fresh air and provide oxygen if breathing is difficult. Get medical attention.

Ingestion — 

Do not give liquids if victim is unconscious or very drowsy. Otherwise, give no more than two glasses 

of water and induce vomiting by giving 30 cc (2 tablespoons) syrup of Ipecac. If Ipecac is unavailable, give two 
glasses of water and induce vomiting by touching finger to back of victim's throat. Keep victim's head below hips 
while vomiting. Get medical attention.

Содержание Termaline 8792 Series































Отзывы: