BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 52

Страница: 52 / 65

Bird SiteHawk Operation Manual

Data Transfer Function

Data transfer from the SK-4500 may be accomplished using a USB Drive or via
Bluetooth transfer. For instructions on how to make transfers see

"Data

Transfer via USB Drive" on page 43

"Data Transfer via Bluetooth" on page

Data Transfer via USB Drive

Data can be transferred from or to the SiteHawk internal memory with the use
of an external USB drive and the USB adapter (supplied).

CAUTION

Do not connect the unit to a PC USB port.

File transfer must be done using a USB Drive.

Connect the USB drive to the USB adapter, then connect the USB adapter to
the USB-C port at the bottom of the unit.

Press Home key on the SiteHawk display.

Select the File Manager icon on the unit’s home screen.

Select Internal Storage (SiteHawk Internal storage Local) from the drop-
down menu in the File Manager program. See

Figure

Navigate to the location of the file.

Figure

File Selection

Select the file to be copied.

Press the Copy icon.

Press the Home screen icon of the file manager.

Select USB Storage from the drop-down menu. See

Figure

Содержание SiteHawk SK-200-TC


































































Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды

BIRD SiteHawk SK-200-TC, Руководство по эксплуатации

Результаты поиска

Содержание SiteHawk SK-200-TC

Отзывы:

Похожие инструкции для SiteHawk SK-200-TC

Бренды по названию

Популярные бренды