BIRD SiteHawk SK-200-TC Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 65

background image

Data Save and Export

44

Figure

39

External Storage

10. Navigate to the directory where the file will be saved.
11. Press the Paste icon to save the file onto the USB drive.
12. Exit the File Manager.
13. Tap Settings on the Home Screen. See

14. Tap Storage, if the storage option is not available see

"Display Storage

Option in Settings" on page 45

.

Figure

40

Unmount USB Storage

15. Scroll to SD Card, and tap Unmount shared storage.
16. Tap OK
17. You may now remove the USB Drive.

«
...
51
52
53
54
55
...
»

Содержание SiteHawk SK-200-TC


































































Отзывы:

Нет отзывов

Похожие инструкции для SiteHawk SK-200-TC

Бренд: Hameg Страницы: 44

Бренд: Hameg Страницы: 60

Бренд: Hameg Страницы: 28

Бренд: HAMAR LASER Страницы: 113

Бренд: VEE GEE Страницы: 2

Бренд: Flytec Страницы: 2

Бренд: QEED Страницы: 6

Бренд: E-Mon Страницы: 72

XL4 SECOND STAGE

Бренд: Apeks Страницы: 21

Бренд: Z-TRAUQ Страницы: 10

Бренд: OLYS Страницы: 2

Бренд: D-tect Systems Страницы: 28

Cerabar S PMC71

Бренд: Endress+Hauser Страницы: 48

Бренд: Keysight Technologies Страницы: 10

Бренд: International Light Technologies Страницы: 19

BlueForce Smart

Бренд: CAME Страницы: 24

Бренд: AL Страницы: 2

Бренд: HEIDENHAIN Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды