Bircher RFGate 2.2.NG, Перевод оригинальной инструкции по эксплуатации

Страница: 2 / 4

2
1 2
ON
1 2
ON
1 2
ON
1 2
ON
IN 1
NC 2x
8K2 8K2 8K2 8K2
i
NC
1
ON
1 2
+
2032
2
ON
1 2
+
+
2032
2032
8K2 8K2 1) 1)
IN 2
2)
8K2 1) 1) 8K2
VCC1 VCC2 COM1 OUT1 SOUT1 COM2 OUT2 SOUT2 TST1 COM.T1 TST2 COM.T2
+/~ –/~
12/24V
AC/DC
COM1
OUT1
COM2
OUT2
COM1
SOUT1
COM2
SOUT2
COM1
OUT1
COM2
OUT2
IN1 comon IN2
2)
DIP switch Sensor
connections
IN1 comon IN2
2)
DIP switch Sensor
connections
IN1 comon IN2
2)
DIP switch Sensor
connections
IN1 comon IN2
2)
DIP switch Sensor
connections
1) Change from NC to NO, see chapter 3.2
3.2 Change input from NC to NO (factory setting = NC)
4.3 DIP switches
3.1 DIP switch setting according to sensor (safety edge, switch contact)
4 Receiver
3 Transmitter
1.
Insert
battery 1
4.
Insert
battery 2
2.
Status
3.
Change
5.
Change
stored
Press button on
transmitter
Status
changes
LED
flashes
LED
flashes 2x
LED
flashes 5x
> 1.5 sec.
After inserting the battery 1,
you have 10 seconds to change the logic
1 2 3 4 5
ON
*
Safety application
standard
according to EN ISO 13849-1
1 2 3 4 5
ON inactive
➔
no safety function!
(Radio connection is not monitored)
1 2 3 4 5
ON Transmission frequency
869.85 MHz: Set DIP-switch before pairing
transmitter – receiver
1 2 3 4 5
ON
*
868.95 MHz: Set DIP-switch before pairing
transmitter – receiver
1 2 3 4 5
ON Test input type
NC
activated = contact open
1 2 3 4 5
ON
*
NO
activated = contact closed
1 2 3 4 5
ON Automatic frequency adjustment
active
used only in case of radio disturbances
1 2 3 4 5
ON
*
inactive
1 2 3 4 5
ON
*
Programming of RF Gate 2.2.A
(2 transmitters)
Transmitter 1 corresponds to output 1
Transmitter 2 corresponds to output 2
1 2 3 4 5
ON Programming of RF Gate 2.2.NG
(1 transmitter)
Input 1 corresponds to output 1
Input 2 corresponds to output 2
* = factory setting
Observe
the sequence
IN1 comon IN2
2)
RFGate 2.2.S RFGate 2.2.S
RFGate 2.2.S.F
Relay contacts are shown unpowered
4.2 Wiring: Outputs and control
Test
Common
Gate control
with
NC input
Gate control
8.2 kOhm
input
Gate control
with
NO input
Remove jumper(s)
4.1 Wiring: Power supply and test inputs
Common
both for IN1 and
IN2
2)
i
Input IN2 and DIP switch 2 only active at RFGate 2.2.NG (see paragraph 4.3, DIP switch 5)
NO 5x
NO