2
3
DESCRIPTIONS (See Fig. 1, 2, 3, 4, & 6)
A. Front panel
B. Pebbles (changeable)
C. Soft Glow Switch
D. Main housing
E. Fixed unit mounting brackets
F. Heat vents
G. Control panel
H. Remote control home
I. Feet x 2 (removable)
J. Digital thermostat (5 presets)
(ONLY for 6500/6700)
K. Mode control
L. Digital timer (6 presets)
M. Flame intensity button
N. ON/OFF switch (main unit only)
O. Thumb screws x4
P. Securing bottom bracket (part not shown)
Q. ON/OFF button remote control
R. Soft Glow
ASSEMBLY INSTRUCTIONS (SEE FIG. 1–6)
Carefully remove all parts and make sure that
they are all present. Ref. to Figs.1-6.
Installing Batteries into the Remote:
Before operation, insert 2 AAA batteries into the
back of the remote control:
• DO NOT mix old and new batteries
• DO NOT mix alkaline, standard (carbon-zinc),
or rechargeable (nickel-cadmium) batteries
The remote control for this unit has the capability
of operating all control panel functions except the
mechanical ON/OFF switch (N). Please note this
remote will not work through walls (See Fig. 3).
Stand Assembly (See Fig. 6):
For floor use attach the two feet assemblies (I)
to the fireplace heater using the 4 thumb screws
(O) provided. Gently lay the main housing
(D) horizontally down without the front panel
attached. Line up each feet assembly using
the metal guides and then screw in two thumb
screws (O) into the corresponding holes. Place
unit upright, add the pebbles (B) and then attach
the front panel by lining up the front panel metal
guides with the main housing panel pins. For wall
mounting see Wall Mount Installation below.
Wall Mount Installation (See Fig. 4 & 5):
This product weighs 40 lbs. Do not install alone.
The following procedure is for a dry wall
installation using the provided hardware.
Note:
If installing on a different type of wall (i.e
cavity wall) or using different hardware please
consult a professional for advice on the correct
way to install the unit.
IMPORTANT:
Before drilling into any wall
ensure no electrical cables are present in the
area. Make sure you allow at least 3 feet of space
on all four sides of unit.
1. Turn unit off and disconnect the unit if in use.
2. Remove front panel and pebbles if installed.
3.
Remove feet assemblies from main housing
by unscrewing the thumb screws.
4.
Decide on the position where the electric
fireplace will hang on the wall. REMEMBER
not to position directly above the power
socket and at least 3 feet away from any
objects on all sides (reference Fig. 5).
5.
Mark on the wall the points between the
centre of the holes on the fixed unit rear
mounting brackets (E) making sure the
points line up and are level (reference Fig. 4)
6.
Drill into the wall using an 8mm drill bit two
holes on the marked points so that you can
fit the appropriate wall plugs.
7.
Screw in two 4 x 35mm screws into the wall
plugs, leaving 10mm of the screws out of the
wall.
8.
Hang the main body of the unit onto the
two exposed screws by lining up the rear
mounting brackets’ holes.
9.
Place the securing bottom bracket (P)
into the rear of the unit and then use one
4x35mm screw to secure the bracket and
unit to the main wall.
10. Add pebbles to the unit, then place the front
panel onto the unit by lining up the front
panel guides with the main housing pins
(located on the side of the housing) and
make sure the unit is secure.
11. Unit is now ready to be turned on and operated.
OPERATING INSTRUCTIONS
• There may be an odor coming from the heater
the first time you use it. This is normal during
the break-in period or after long term storage.
Make sure the heater is in a well ventilated
area and continue running it until the smell
goes away.
• You may hear a popping or crackling sound as
the heater heats up. This is normal and safe
operation.
• The Fireplace Heater can be operated by
using the remote control (Fig. 3) or the control
panel (Fig. 2) located on the side of the unit.
• Place the heater on a firm, level surface or
mount on wall.
• Avoid overloading your circuit by not using
other high wattage appliances in the same
outlet.
HEATER SAFETY
PLEASE READ AND SAVE THESE
IMPORTANT SAFEGUARDS
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock, and injury to persons,
including the following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance
directly into a 120V AC electrical outlet.
3. The heater is hot when in use. To avoid burns,
DO NOT let bare skin touch hot surfaces.
Use handle when moving this heater. Keep
combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least
3 ft (0.9 m) from the front of the heater and keep
them away from the sides and rear.
4. DO NOT run cord under carpeting. DO NOT
cover cord with throw rugs, runners, or the like.
Arrange cord away from traffic area and where it
will not be tripped over.
5. This heater is not intended for use in bathrooms,
laundry areas and similar indoor locations.
NEVER locate heater where it may fall into a
bathtub or other water container.
6. Extreme caution is necessary when any heater is
used by, or near children or invalids, and whenever
the heater is left operating and unattended.
7. Always unplug the heater when not in use.
8. When unplugging, be sure to pull by the plug
and not the cord.
9. DO NOT insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause
an electric shock or fire, or damage the heater.
10. DO NOT operate heater with a damaged cord
or plug, or after the heater malfunctions, or has
been damaged in any manner. Return appliance
to manufacturer for examination, electrical or
mechanical adjustment, or repair.
11. A heater has hot and arcing or sparking parts
inside. DO NOT use it in areas where gasoline,
paint, or flammable liquids are used or stored.
12. Use appliance only for intended household use
as described in this manual. Any other use not
recommended by the manufacturer may cause
fire, electric shock, or injury to persons. The use
of attachments not recommended or sold by the
manufacturer may cause hazards.
13. DO NOT use outdoors.
14. To prevent a possible fire, DO NOT block air
intakes or exhaust in any manner. DO NOT use
on soft surfaces like a bed, where openings may
become blocked.
15. To disconnect heater, press the On/Off button,
then remove plug from outlet.
16. Always plug heaters directly into a wall outlet/
receptacle. Never use with an extension cord or
relocatable power tap (outlet/power strip).
17. If the heater will not operate, see specific
instructions under Auto Safety Shut-off on
resetting the heater.
18. DO NOT attempt to repair or adjust any electrical
or mechanical functions on this unit. Doing so
will void your warranty. The inside of the unit
contains no user serviceable parts. All servicing
should be performed by qualified personnel only.
19. DISCONTINUE USE IF PLUG OR OUTLET IS
HOT. RECOMMEND OUTLET BE REPLACED IF
PLUG OR OUTLET IS HOT TO TOUCH.
20. The remote control contains a magnet to help
affix the control to the main unit when not in use.
Please only place the remote control on the unit
where the remote control home is marked (H).
21.
WARNING:
In order to avoid overheating, do not
cover the heater.
22.
WARNING:
This heater is not equipped with a
device to control the room temperature. Do not
use this heater in small rooms when they are
occupied by persons not capable of leaving the
room on their own, unless constant supervision
is provided.
PLEASE SAVE THESE
INSTRUCTIONS
CONSUMER SAFETY INFORMATION
THIS APPLIANCE HAS A
POLARIZED PLUG (one blade is
wider than the other). To reduce
the risk of electric shock, this plug
is intended to fit in a polarized
outlet only one way. If the plug
does not fit fully in the outlet,
reverse the plug. If it still does not
fit, contact a qualified electrician to
install the proper outlet.
CAUTION:
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT
DO NOT ATTEMPT TO MODIFY THIS PLUG OR
DEFEAT THIS SAFETY FEATURE IN ANY WAY
.
TECHNICAL SPECIFICATIONS
Amps: 12.5
Wattage: 1500W/ (+ 5% - 10%)
Working Voltage: 120V AC/60 HZ
Bulb Type: 3.2w Max Type 27 pcs LED Bulbs
Avoid overloading your circuit by not using other
high wattage appliances in the same outlet. At 1500
Watts, this unit draws 12.5 Amps.
ASSEMBLY INSTRUCTIONS
Please make sure to check packaging for parts that
could be used to operate your heater.
This package includes:
1 - Fireplace Heater
1 - Remote Control
2 - AAA Batteries for Remote
2 - Feet
4 - Thumb Screws (for feet)
1 - Wall Mount
Hardware Kit
P
BEF6500LED_BEF6700LED-CN_14EFM1.indd 4-5
6/30/14 8:52 AM