Caring for your unit
Your unit should not be allowed to get wet or be left in excessive sunlight. It may be
cleaned regularly using a soft cloth, lightly dampened in soapy water. Do not allow the
interior of your unit to become wet. Do not use detergents, alcohol, spray aerosols or
strong solvents on your unit.
Access to the interior of the unit is not required for maintenance purposes.
If your unit is damaged, you should not use it but should return it to
SLENDERTONE
or your
local distributor for replacement or repair. Repairs, service and modifications may not be
carried out by anyone other than qualified service personnel authorised by
SLENDERTONE
.
IMPORTANT
:
Under no circumstance should anything other than the correct type of batteries
– (rechargeable batteries 3.6V NiMH) be used with your unit. These can be purchased
from the
SLENDERTONE
careline.
Disposing of the pads and batteries
Used pads and batteries must never be disposed of in a fire but in accordance with your
country’s national laws governing the disposal of such items.
NOTES
:
The signal gradually increases to a peak intensity level at the start of the contraction
phase (i.e. ramp up) and gradually decreases to nothing at the start of the relaxation
phase (i.e. ramp down). When the symbol is flashing, the stimulus is significantly
reduced.
Accessories:
You can purchase all accessories at www.slendertone.com. Under no circumstances
should anything other than
SLENDERTONE
accessories be used with your
SLENDERTONE
charger
or
SLENDERTONE
unit (Type 390). Any others may not be compatible with your unit and
could degrade the minimum safety levels.
SLENDERTONE ABS
Female Belt (E:70)
SLENDERTONE ABS
Male Belt (X:70)
SLENDERTONE ABS
Pads
:
• 1 large adhesive pad (Type 706 or 709)
• 2 small adhesive pads (Type 707 or 710)
SLENDERTONE BOTTOM
(E:30)
SLENDERTONE BOTTOM
Pads:
• 4 large adhesive pads (Type 716)
SLENDERTONE ARMS ACCESSORY
Female (E:60)
SLENDERTONE ARMS ACCESSORY
Male (X:60)
SLENDERTONE ARMS
Pads:
• 4 small adhesive pads - Female (Type 715)
• 4 small adhesive pads - Male (Type 718)
SLENDERTONE
Belt Extension
Battery Pack (3.6V, NiMH)
Battery Charger (EU - 2504-0303)
Battery Charger (US/Japan - 2504-0302)
Charger complies to EN 60950, Input: nominal voltage 100-240V, frequency 50-60Hz, current
125mA. Do not use any other chargers or any other power supplies.
Product Type:
394
Intended use:
Muscle stimulator
Classification:
Internally powered equipment, Class II charger, Type BF applied parts.
technical specifications
Waveform:
Symmetrical bi-phasic square waveform when measured into a resistive load.
Environmental Specifications:
Operating:
Temperature Range: 0 - 35°C (32 - 95°F)
Humidity: 20 - 65 % RH
Storage:
Temperature Range: 0 - 35°C (32 - 95°F)
Humidity: 20 - 85 % RH
Attention:
This unit can deliver currents in excess of 2mA/cm2 if used with incorrect electrodes.
Description of your unit’s symbols:
There are a number of technical markings on your unit. These can be explained as follows:
The unit and garments are manufactured for Bio-Medical Research Ltd, Parkmore Business
Park West, Galway, Ireland.
The unit requires 1 x 3.6 volt (NiMH) DC battery pack DC is indicated by the symbol:
The Output Frequency indicates the number of pulses per second transmitted by the unit. This
is measured in hertz, which is indicated by “Hz”.
Output (RMSA) means the maximum output root mean square current for each channel.
Output (RMSV) means the maximum output root mean square voltage for each channel.
This symbol means “Attention, consult the accompanying documents”.
This symbol means type BF applied parts.
This symbol on your unit is to indicate conformity to the requirements of the Medical
Device Directive (93/ 42/EEC). 0366 is the number of the notified body (VDE).
Conforms to UL STD 60601-1.
Certified to CAN/CSA.
STD C22.2 NO 601.1
SN stands for ‘serial number’. Inside the box, on the back of the unit is the serial number spe-
cific to this unit. The letter preceding the number indicates the year of manufacture, where “P”
denotes 2010, “Q” denotes 2011 etc.
The garments’ batch number is represented on their packaging, by the number corresponding
with the LOT symbol.
At the end of the product lifecycle, do not throw this product into the normal household
garbage, but bring it to a collection point for the recycling of electronic equipment.
Some product materials can be re-used if you bring them to a recycling point. By re-using
some parts or raw materials from used products you make an important contribution to
the protection of the environment. Please contact your local authorities if you need more
information about collection points in your area.
Waste Electrical and Electronic Equipment can have potentially harmful effects on the
environment. Incorrect disposal can cause harmful toxins to build up in the air, water and
soil and can be harmful to human health.
!
0366
15
14
English
Resize Slendertone Arms IM Backups_Layout 1 26/10/2011 11:32 Page 16
