manualshive.com logo in svg

bintec elmeg RM3000, Руководство по установке

Поделиться
Скачать
bintec elmeg RM3000 Скачать руководство пользователя страница 31

4.10 IC Statement

4.10.1 CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ-
ing interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de li-
cence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscept-
ible d'en compromettre le fonctionnement.

This device and its antennas(s) must not be co-located or operating in conjunction with any other antenna or trans-
mitter except in accordance with IC multi-transmitter product procedures.

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre
antenne ou transmetteur.

4 Compliance

bintec elmeg

26

RM3000 Router

Содержание RM3000








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды