94VT (.052”) 1.3mm Carbide Tip
94P, 97P
54-3950
901VT (.066”) 1.6 mm Carbide Tip
54-3951
903 (.079”) 2.0 mm
54-3941/54-3940
905 (.089”) 2.3 mm
54-3941/54-3940
905VT (.088”) 2.3 mm Carbide Tip
905P
54-3952
906 (.100”) 2.5 mm
54-3941/59-3940
909 (.111”) 2.8 mm
54-3941/54-3940
909VT (.112”) 2.8 mm Carbide Tip
54-3953
STANDARD FLUID NOZZLES
FLUID NOZZLES
90F (.030") 0.8 mm
54-4022
91F (.040") 1.0 mm
95P, 97P
54-4023
92F (.046") 1.2 mm
92P, 93P*
54-4024
94F (.055") 1.4 mm
95AP**
●
54-4026
97F (.070") 1.7 mm
97AP**
●
54-4029
5
ULTRA LIGHT / Reduced Flow
89 (.020” Dia.) 0.5 mm
SEE NOTE
VERY LIGHT / Reduced Flow
90 (.030” Dia.) 0.8 mm
90P***
LIGHT: less than15 to 20 seconds in a Zahn 2 Cup,
91 (.040” Dia.) 1.0 mm
95P, 97P,
e.g., stains, varnishes,thin lacquers, automotive refinishing fluids.
92 (.046” Dia.) 1.2 mm
92P*,
54-3941
MEDIUM: 20 to 60 seconds in a ZAHN 2 Cup,
93 (.051” Dia.) 1.3 mm
95AP, 97AP**
e.g., general industrial coatings.
94 (.055” Dia.) 1.4 mm
93P*, 94P
95 (.059” Dia.) 1.5 mm
96 (.063” Dia.) 1.6 mm
HEAVY: greater than 60 seconds in a Zahn 2 Cup.
97 (.070” Dia.) 1.7 mm
FLUID
FLUID NOZZLE NO.
APPLICABLE
AIR NOZZLE
FLUID
NEEDLE
NOTE:
Use stainless steel Fluid Needle (54-3941) for all above nozzles. Optional nylon-tipped stainless steel Fluid Needle (54-3940) is also avaible.
Binks Needles AB and ABSS (54-3609 & 54-3616) may be used, but require readjustment of the needle cap and locknut position.
SPECIAL PURPOSE NOZZLES
TYPICAL APPLICATION
FLUID NOZZLE NO.
APPLICABLE
AIR NOZZLE
COMPATIBLE
FLUID
NEEDLE
VERY HEAVY FLUIDS:
Block Fillers, Texture Coatings, Fire
Retardants, Road Marking Paint,
Bitumastics, Adhesives, Celluar
Plastisols, Underbody & Vitreous
Coatings, Special Applications
FEATHERING
For applications requiring more
gradual fluid valve opening for
metering control of fluid flow
with trigger
SIPHON FEED-FINE FINISH
Light to medium fluids
Auto body spot repairs
Medium to heavy fluids
Auto body overall finishing
94s (.055") 1.4 mm
54-4026
95AS
●
97s (.070") 1.7 mm
54-4029
GS FLUID NOZZLES
LIGHT/MEDIUM: less than15 to 20 seconds in a Zahn 2 Cup,
92GS (.046” Dia.) 1.2 mm
SEE NOTE
e.g., stains, varnishes,thin lacquers, automotive refinishing materials.
93GS (.052” Dia.) 1.3 mm
94GS (.055” Dia.) 1.4 mm
MEDIUM: 20 to 60 seconds in a ZAHN 2 Cup,
95GS (.059” Dia.) 1.5 mm
96G
■
54-4547
e.g., general industrial coatings.
96GS (.063” Dia.) 1.6 mm
97GS (.070” Dia.) 1.7 mm
FLUID
FLUID NOZZLE NO.
APPLICABLE
AIR NOZZLE
FLUID
NEEDLE
NOTE:
Optimum setup for clear coat spray is 92GS Fluid Nozzle x 96G Air Nozzle Assembly.
* 93P Low Volume Nozzle for automotive fine finish.
92P Low Volume Nozzle for general industrial.
** 95AP High Solids Nozzle for hard to atomize
coatings and higher flow rates.
97AP Same as 95AP, but for wider fan if needed.
*** 90P Low Volume Nozzle, 1 1/2 H.P. Compressor or
bigger – (6 C.F.M) required.
●
95AP, 95AS and 97AP Air Nozzles do not require
separate Retainer Ring.
■
Improves atomization, breaks-up high solid material
easier, provides better finish at lower pressures and
reduces orange-peel dramatically.
54-4547 needle must be used in conjunction
with the GS fluid nozzle and 96G air nozzle.
96G Air Nozzle
92GS Fluid Nozzle
(.046") 1.2 mm
54-4547 CSS Needle
(Needs to be adjusted to fit your gun.
See adjustment guide at right.)
NEEDLE ADJUSTMENT LENGTH
(See adjustment guide at right.)
Needle
Adjustment Guide
Model
Length
MACH 1
5.8 in.
MACH 1SL
5.7 in.
M1-Gravity
5.5 in.
OPTIONAL GS FLUID
NOZZLE SIZES
Diameter
Nozzle
Inches
mm
92GS
.046
1.2
93GS
.051
1.3
94GS
.055
1.4
96GS
.063
1.6
Example:
93GS Fluid Nozzle,
96G Air Nozzle &
54-4547 Needle.
